The mechanical behavior of asphalt mixture under high stresses presents nonlinear viscoelasticity and permanent deformation. In this paper, a nonlinear fractional viscoelastic plastic (NFVEP) creep model for asphalt mixture is proposed based on the Nishihara model, with a Koeller spring-pot replacing the Newton dashpot. The NFVEP model considers the instantaneous elasticity, viscoelasticity with damage and time-hardening viscoplasticity with damage concurrently, and the viscoelastic response is modeled by fractional derivative viscoelasticity. To verify the model, uniaxial compressive creep tests under various stresses ranging from 0.4 MPa to 0.8 MPa were carried out at room temperature. The NFVEP model predictions are in good agreement with the experiments. The comparison with the modified Nishihara model and the Burgers model reveals the advantages of the NFVEP model. The results show that the NFVEP model, with the same set of parameters, can not only describe the primary and steady-state creep stages of asphalt mixture under low stress levels but also the whole creep process, including the tertiary creep stage, of asphalt mixture under high stress levels.
Temperature–frequency sweep tests were performed on silicone rubber to investigate the dynamic viscoelastic properties. The test results show that the viscoelasticity of silicone rubber presents significant temperature dependence and frequency dependence. The dynamic viscoelastic test curves at different temperatures can be shifted along the logarithmic frequency coordinate axis to construct smooth master curves at the reference temperature of 20 °C, covering a frequency range of 10 decades, which indicates thermorheological simplicity on a macro level and frequency temperature equivalence of the silicone rubber material in the experimental temperature range. The van Gurp–Palmen plot and Cole–Cole plot for the test data at various temperatures merge into a common curve, which further validates thermorheological simplicity. The temperature dependent shift factors of silicone rubber material were well characterized by the Williams–Landel–Ferry equation. Moreover, the fractional-order differential Kelvin (FDK) model, the fractional-order differential Zener (FDZ) model, and the improved fractional-order differential Zener (iFDZ) model were used to model the asymmetric loss factor master curve. The result shows that the iFDZ model is in good agreement with the test results, indicating that this model is suitable for describing the asymmetry of dynamic viscoelastic properties of silicone rubber.
In order to quantitatively describe the time-varying mechanical properties of asphalt mixture during creep process, a nonlinear viscoelastoplastic creep model was proposed, by using variable-order fractional calculus. The differential order of the variable-order fractional element of the model is no longer constant, but a variable that changes with time, which reflects the changes of the mechanical properties of the material during the creep process. Whereas the tertiary creep phase is modeled by the viscoplastic element with time-varying viscosity, which is attributed to damage evolution. The uniaxial creep compression tests of AC-13C asphalt mixture under different stress levels (0.7 MPa, 0.9 MPa, 1.1 MPa, 1.3 MPa, 1.5 MPa, 1.7 MPa) were carried out with MTS-809 testing machine at 25 °C, and the test results were analyzed by the model using Levenberg–Marquardt optimization algorithm. It is shown that creep damage occurs when the applied stress exceeds a certain critical value, and the damage incubation time depends on the applied stress level. The higher stress decreases the damage incubation time. The model is in good agreement with the experimental results, and is applicable to describe the entire creep process, which consists of primary, steady and tertiary stages. Moreover, the variation of the model parameter can describe the change of viscoelastic properties of the material during the creep process. The differential order of the variable-order fractional element is constant during the primary creep stage, indicating that the creep behavior of the asphalt mixture is linear viscoelastic in small strain range. For the same stress level, the fractional order of the steady creep stage is greater than that of the primary creep stage, and it increases with the increasing stress level, which shows that the viscous behavior in the steady creep is more remarkable than that in the primary creep, and the higher the stress level, the more prominent the viscous performance exhibits.
Below the incipient characteristic tearing energy (T0), cracks will not grow in rubber under fatigue loading. Hence, determination of the characteristic tearing energy T0 is very important in the rubber industry. A rubber cutting experiment was conducted to determine the T0, using the cutting method proposed originally by Lake and Yeoh. Then, a fatigue crack propagation experiment on a edge-notched pure shear specimen under variable amplitude loading was studied. A method to obtain the crack propagation rate da/dN from the relationship of the crack propagation length (Δa) with the number of cycles (N) is proposed. Finally, the T0 obtained from the cutting method is compared with the value decided by the fatigue crack propagation experiment. The values of T0 obtained from the two different methods are a little different.