Airborne microplastic is an emerging and widespread pollutant yet is still under-characterised and insufficiently understood. Detailed description of microplastic air pollution is crucial as it has been identified in human lungs and remote locations, highlighting the atmosphere as a medium of MP dispersion and transportation. The lack of standardization of methods for measuring and further monitoring of microplastic pollution is an obstacle towards assessment of health risks. Since the first recognition of MP presence in the atmosphere of Krakow in 2019, this research was conducted to further characterise and develop the methods for qualitative and quantitative analysis of airborne microplastic (attenuated total reflectance-Fourier transform infrared spectroscopy (ATR-FTIR); pyrolysis-gas chromatography–mass spectrometry (Py-GC–MS); scanning electron microscopy-energy dispersive spectroscopy SEM-EDS) and pre-treatment of samples. The data were gathered in seven cycles from June 2019 to February 2020. The methods used in the study allowed the identification and analysis of the changing ratio of the different types of synthetic polymers identified in the atmospheric fallout (low-density polyethylene, nylon-66, polyethylene, polyethylene terephthalate, polypropylene and polyurethane). Observations of interactions between microplastic particles and the environment were conducted with analyses of surface changes due to degradation. Different phases attached to the microplastics surfaces, with some of the inorganic contaminants transported on these surfaces determined also to be of anthropogenic origin. The methodology proposed in this study allows further characterisation of microplastic from multiple locations to provide highly comparable data, leading to identification of the sources of this phenomenon, as well as seasonal changes.

The increasing use of plastic (synthetic polymers) results in the release of uncontrollable amounts of synthetic materials into the environment through waste, infrastructure, and essential goods. As plastic materials undergo weathering, a complex process unfolds, leading to the formation of pollutants, notably microplastics. This study employs multiple instrumental methods to explore the intricate abiotic degradation of the five most commonly used synthetic polymers in environmentally relevant conditions. An extensive set of analytical techniques, along with chemometric analysis of the results of Raman spectroscopy, was used to characterize the materials and evaluate the nature and extent of degradation caused by artificial weathering under temperature, humidity, and solar-like irradiation cycles. Investigation focuses on the link between abiotic weathering and the generation of micro- and nanoplastics, accompanied by molecular and surface adhesion changes, and the release of additives such as metals and metal oxides. Research reveals that microplastics may exhibit varied physical properties due to the incorporation of significant quantities of high-density additives from the parent plastic, which might influence the extraction methods and the transportation models' accuracy. At the molecular and microscopic scales, non-homogeneous pathways through which plastic decomposes during weathering were observed. The formation of additive-polymer combinations might play a pivotal role in the monitoring approaches for microplastics, presenting unique challenges in assessing the environmental impact of different plastic types. These findings offer complex insight into abiotic weathering, microplastics' generation, and the influence of additives that were previously overlooked in toxicity and health assessment studies. As plastic pollution continues to escalate, understanding these complex processes is crucial for microplastic monitoring development and adopting effective preventative measures.

In the face of material shortages, growing environmental awareness, and technical advancement, incinerated waste materials are being considered secondary resources. Especially incinerated sewage sludge ash is of interest due to its massive and increasing production and relatively stable composition with a satisfying concentration of elements of value. This paper revises the basic methods for recovery of valuable components from incineration sewage sludge and simultaneous removal or stabilization of elements that may negatively influence the environment with further ash usage or storage. The presented work focuses on collating and analysing the efficiency of currently used approaches as well as their limitations and perspectives for future development. Chemical methods analysed include acidic and alkaline leaching, chelating, and sequential leaching. Due to scarce examples from literature, the exploration of a microbiological approach focuses on the mechanisms and potential for application of different microorganisms for element extraction. The methods described are relatively efficient and affordable, yet still need further development. Specifically, microbiological approaches are rarely used for incineration sewage sludge treatment regardless of their potential advantages over other approaches. Constant mineral and chemical composition within one incineration plant can vary among plants due to many factors, so a well-established range of techniques and an individual approach are important.

The relation between rotation speed, air pressure and the velocity of air-rotary drilling using the down the hole method is determined in an empirical manner. For the study, velocity measurements are obtained for combinations of the aforementioned parameters during fieldwork for the installation of borehole heat exchangers near Lublin, Poland. The tests consider three drill bit diameters—110, 127 and 140 mm; three rotational speeds—20, 40 and 60 1/min; and three air pressures—16, 20 and 24 bar. The borehole heat exchangers need 100 m deep wells. The lithology consists mainly of loess and clays to 24 m, sand and carbonate rocks to 36 m, and marls and limestone to 100 m. It is found that the highest drilling velocity is achieved when the greatest pressure is applied, while the lowest drilling velocity is connected to the lowest pressure. However, the relation between rotation speed and drilling velocity is more complex, as drilling velocity seems to be more affected by depth. Therefore, lithology can be a major factor. The results may find direct use in drilling, and provide a basis for further studies on the optimization of drilling technology.

Microplastics (MPs) are considered an important stratigraphic indicator, or ‘technofossils’, of the Anthropocene. Research on MP abundance in the environment has gained much attention but the lack of a standardized procedure has hindered the comparability of the results. The development of an effective and efficient method of MP extraction from the matrix is crucial for the proper identification and quantifying analysis of MPs in environmental samples. The procedures of density separation used currently have various limitations: high cost of reagents, limited solution density range, hazardous reagents, or a combination of the above. In this research, a procedure based on density separation with the use of potassium formate water solution (H₂O/KCOOH) in controlled conditions was performed. Experimental sediment mixtures, spiked with polyethylene (PE), polystyrene (PS), polyurethane (PUR) and polyethylene terephthalate (PET) particles were prepared and an extraction procedure was tested in the context of a weight-based quantitative analysis of MPs. This article discusses the effectiveness and safety of the method. It additionally provides new information on the interactions between MP particles and the mineral matter of the sediment. Results were acquired with the use of instrumental methods, namely thermogravimetry (TG), Fourier Transform Infrared (FTIR) spectroscopy, Field Emission Scanning Electron microscopy and Energy Dispersive spectrometry (SEM/EDS), as well as X-ray fluorescence (XRF) analysis.

The endophytic Basidiomycete Sporobolomyces ruberrimus protects its host Arabidopsis arenosa against metal toxicity. Plants inoculated with the fungus yielded more biomass and exhibited significantly fewer stress symptoms in medium mimicking mine dump conditions (medium supplemented with excess of Fe, Zn and Cd). Aside from fine-tuning plant metal homeostasis, the fungus was capable of precipitating Fe in the medium, most likely limiting host exposure to metal toxicity. The precipitated residue was identified by Fourier transform infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS), X-Ray Diffraction (XRD) and electron microscopy (SEM/TEM) with energy dispersive X-Ray analysis (EDX/SAED) techniques. The performed analyses revealed that the fungus transforms iron into amorphous (oxy)hydroxides and phosphates and immobilizes them in the form of a precipitate changing Fe behaviour in the MSR medium. Moreover, the complexation of free Fe ions by fungi could be obtained by biomolecules such as lipids, proteins, or biosynthesized redox-active molecules.