Carmen Catalina Rusu

Dr. Carmen Catalina Rusu

"Dunarea de Jos" University of Galati, Galaţi, Romania
orcid

Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
9 June 2021 in Metals
Verified
Journal Article
Open access
PDF file
MCMukti Chaturvedi
Mukti Chaturvedi
Elena SCUTELNICUElena SCUTELNICU
Elena SCUTELNICU
CRCarmen Catalina Rusu
Carmen Catalina Rusu
LMLuigi Renato Mistodie
Luigi Renato Mistodie
DMDanut Mihailescu
Danut Mihailescu
ASArungalai Vendan S
Arungalai Vendan S
Wire arc additive manufacturing (WAAM) is a fusion manufacturing process in which the heat energy of an electric arc is employed for melting the electrodes and depositing material layers for wall formation or for simultaneously cladding two materials in order to form a composite structure. This directed energy deposition-arc (DED-arc) method is advantageous and efficient as it produces large parts with structural integrity due to the high deposition rates, reduced wastage of raw material, and low consumption of energy in comparison with the conventional joining processes and other additive manufacturing technologies. These features have resulted in a constant and continuous increase in interest in this modern manufacturing technique which demands further studies to promote new industrial applications. The high demand for WAAM in aerospace, automobile, nuclear, moulds, and dies industries demonstrates compatibility and reflects comprehensiveness. This paper presents a comprehensive review on the evolution, development, and state of the art of WAAM for non-ferrous materials. Key research observations and inferences from the literature reports regarding the WAAM applications, methods employed, process parameter control, optimization and process limitations, as well as mechanical and metallurgical behavior of materials have been analyzed and synthetically discussed in this paper. Information concerning constraints and enhancements of the wire arc additive manufacturing processes to be considered in terms of wider industrial applicability is also presented in the last part of this paper.

16 May 2021 in Metals
Verified
Journal Article
Open access
PDF file
Elena SCUTELNICUElena SCUTELNICU
Elena SCUTELNICU
MIMihaela Iordachescu
Mihaela Iordachescu
CRCarmen Catalina Rusu
Carmen Catalina Rusu
DMDanut Mihailescu
Danut Mihailescu
José L. OCAÑAJosé L. OCAÑA
José L. OCAÑA
This paper addresses the metallurgical and mechanical characterization of dissimilar joints made by laser autogenous welding between thin sheets of low-carbon steel (CS) and austenitic stainless steel (SS). The welding technology applied, previously optimized to produce sound dissimilar joints, is based on the heat source displacement from the weld gap centerline towards CS, in order to reduce the SS overheating. The research includes optical microscopy observations, energy dispersive X-ray analysis (EDX) to assess the wt% of Cr, Ni, and Fe in all regions of the dissimilar welded joint, hardness measurements, and tensile tests of transverse-welded flat specimens. In comparison with classical determination of the joint overall mechanical characteristics, the novelty of this research consists of experimental assessment of the local mechanical behavior of the fusion and heat affected zones by using a digital image correlation technique (VIC-2D). This is an efficient tool for determining the constitutive properties of the joint, useful for modelling the mechanical behavior of materials and for verifying the engineering predictions. The results show that the positive difference in yielding between the weld metal and the base materials protects the joint from being plastically deformed. As a consequence, the tensile loading of flat transverse specimens generates the strain localization and failure in CS, far away from the weld.

5 April 2017 in Materials and Manufacturing Processes
Verified
Journal Article
Closed access
TCT. Chinnadurai
T. Chinnadurai
SVS. Arungalai Vendan
S. Arungalai Vendan
CRCarmen Catalina Rusu
Carmen Catalina Rusu
Elena SCUTELNICUElena SCUTELNICU
Elena SCUTELNICU
The polypropylene material meets the needs and requirements in automotive industry due to its features such as wide range of physical properties, ease of processing, and low cost. This research has focused on the investigation of the behavior of polypropylene during ultrasonic welding process. The lap welded samples were examined by modern methods such as Differential Scanning Calorimetry (DSC), Thermogravimetric Analysis (TGA), and Fourier Transform Infrared Spectroscopy (FTIR). Also, the morphology of the non-welded and welded regions of the polypropylene samples was analyzed by Scanning Electronic Microscopy (SEM) method. TGA and DSC results showed a negligible difference between the mass loss of the molded and the welded propylene materials. Furthermore, the SEM images revealed the formation of voids in close correlation with vibration amplitude. The weld strength and bond integrity appears to be higher for higher vibrations, emphasizing that the lap joint interface strength is higher when the tendency of voids formation is decreasing. The stress-strain curve of the material, plotted for three ultrasonic welding variants, illustrated that increasing the main process parameters (pressure, time, and vibration amplitude) makes the weld strength higher, but a decrease in plasticity was noticed in the welded polypropylene samples.

6 November 2023 in Materials
Verified
Journal Article
Open access
PDF file
MCMukti Chaturvedi
Mukti Chaturvedi
ASArungalai Vendan S
Arungalai Vendan S
GSGeorge Simion
George Simion
CRCarmen Catalina Rusu
Carmen Catalina Rusu
Elena SCUTELNICUElena SCUTELNICU
Elena SCUTELNICU
Magnetically Impelled Arc Butt (MIAB) welding is a cutting-edge joining method that replaces the conventional welding procedures such as resistance, friction, flash and butt welding. It is a solid-state process that uses a rotating arc to heat up the butt ends of tubes, being followed by a forging process that completes the joining of the workpieces The magnetic flux density and the current interact to develop the Lorentz force that impels the arc along the faying surfaces. This process is found to produce high tensile strength and defect-free welds in ferrous materials and for this reason, it is predominantly employed in automobile applications for joining metallic tubes. Also, this joining procedure can be applied in the fabrication of boilers, heat exchangers, furnace piping in petrochemical industry and other safety-critical high-pressure machinery parts. The MIAB method has several advantages such as a shorter welding cycle, lower input energy requirement and lower loss of material. Compared to other solid-state welding processes, the MIAB welding has an important advantage in terms of cost-efficient welds with better control and reliability. Moreover, there are researchers who have investigated the joining of non-ferrous dissimilar materials using this welding procedure. The studies have been focused on process parametric analysis that involves optimizing and forecasting the magnetic field and thermal profile distribution. This review article provides competitive insights into various design features, computational methods, tests and material characterization, technical issues and workarounds, as well as automation aspects related to the MIAB-welding process. This work will prove to be a quick reference for researchers, useful to identify the research gaps and conflicting ideas that can be further explored for advancements in joining the similar and dissimilar materials.

18 December 2019 in Annals of Dunarea de Jos University of Galati. Fascicle XII, Welding Equipment and Technology
Verified
Journal Article
Open access
PDF file
CRCarmen Catalina Rusu
Carmen Catalina Rusu
SBS. Belaid
S. Belaid
LML. R. Mistodie
L. R. Mistodie
SAS. Adjerid
S. Adjerid
The research focused on the elaboration of the Condition-Based Maintenance (CBM) for the optimization of Smart Manufacturing Processes (SMP) using three types of condition monitoring (CM). The paper presents some considerations regarding the Smart Manufacturing Processes (SMP), especially focused on the Additive Manufacturing (AM) process, by Fused Deposition Modelling (FDM) technology and the way in which the CM and mathematical and probabilistic models can be used, for achieving CBM. The experiments focused on testing three different types of CM: vibration (by vibrometers), sound (by sound level meters) and temperature (by thermal camera and infrared thermography). The experiments and results were analysed, data were processed and a probabilistic model was designed, based on statistical methods, using features/key indicators and their thresholds values. Furthermore, a specific model based on Bayesian network was developed, for achieving CBM of the SMP, specifically to the AM/FDM process. This technique and approach can represent a successful integration of a large number of data monitoring sets and complex modelling and analysis capabilities which can lead in the end to an optimisation of the SMP.

29 September 2025 in Applied Sciences
Verified
Journal Article
Open access
PDF file
AOAlexandru Vladut Oprea
Alexandru Vladut Oprea
RCRobert Ciocoiu
Robert Ciocoiu
GCGeorge Constantin
George Constantin
CRCarmen Catalina Rusu
Carmen Catalina Rusu
Ionelia VoiculescuIonelia Voiculescu
Ionelia Voiculescu
Welding is a technological variant of the electric resistance spot-welding process in which the machined protrusion on the surface is heated and rapidly deformed, and the small molten zone formed at the interface is then forged to form the weld spot. The paper analyses the effects of projection welding parameter values for thin, low-carbon aluminized steel sheets. Two sets of 16 welded samples having three or five protrusions were performed and analyzed using the Taguchi method. The microstructural aspects were analyzed in cross sections made through the welded points, highlighting the expulsion or accumulated effects of the Al-Si alloy protective layer and the formation of intermetallic compounds. To estimate the effect of welding parameters, the samples were subjected to tensile strength tests, and the fracture mode was evaluated. It was found that the values of the breaking forces were close for the two types of samples analyzed, for identical values of the welding regime parameters, but the elongation at break was double in the case of samples with five protrusions. The breaking force increased from 10.9 kN for samples with three protrusions to 11.4 kN for samples with five protrusions, for the same values of welding parameters.