George Simion

Mr. George Simion

"Dunarea de Jos" University of Galati, Galaţi, Romania
orcid

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
11 August 2022 in Materials
Verified
Journal Article
Open access
PDF file
AMAndrei Mitru
Andrei Mitru
ASAugustin Semenescu
Augustin Semenescu
GSGeorge Simion
George Simion
Elena SCUTELNICUElena SCUTELNICU
Elena SCUTELNICU
Ionelia VoiculescuIonelia Voiculescu
Ionelia Voiculescu
The welding process of dissimilar metals, with distinct chemical, physical, thermal, and structural properties, needs to be studied and treated with special attention. The main objectives of this research were to investigate the weldability of the dissimilar joint made between the 99.95% Cu pipe and the 304L stainless steel plate by robotic Gas Tungsten Arc Welding (GTAW), without filler metal and without preheating of materials, and to find the optimum welding regime. Based on repeated adjustments of the main process parameters—welding speed, oscillation frequency, pulse frequency, main welding current, pulse current, and decrease time of welding current at the process end—it was determined the optimum process and, further, it was possible to carry out joints free of cracks and porosity, with full penetration, proper compactness, and sealing properties, that ensure safety in operating conditions. The microstructure analysis revealed the fusion zone as a multi-element alloy with preponderant participation of Cu that has resulted from mixing the non-ferrous elements and iron. Globular Cu- or Fe-rich compounds were developed during welding, being detected by Scanning Electron Microscope (SEM). Moreover, the Energy Dispersive X-ray Analysis (EDAX) recorded the existence of a narrow double mixing zone formed at the interface between the fusion zone and the 304L stainless steel that contains about 66 wt.% Fe, 18 wt.% Cr, 8 wt.% Cu, and 4 wt.% Ni. Due to the formation of Fe-, Cr-, and Ni-rich compounds, a hardness increase up to 127 HV0.2 was noticed in the fusion zone, in comparison with the copper material, where the average measured microhardness was 82 HV0.2. The optimization of the robotic welding regime was carried out sequentially, by adjusting the parameters values, and, further, by analyzing the effects of welding on the geometry and on the appearance of the weld bead. Finally, employing the optimum welding regime—14 cm/min welding speed, 125 A main current, 100 A pulse current, 2.84 Hz oscillation frequency, and 5 Hz pulse frequency—appropriate dissimilar joints, without imperfections, were achieved.

24 March 2022 in Metals
Verified
Journal Article
Open access
PDF file
Ionelia VoiculescuIonelia Voiculescu
Ionelia Voiculescu
VGVictor Geantă
Victor Geantă
ESElena Violeta Stefanescu
Elena Violeta Stefanescu
GSGeorge Simion
George Simion
Elena SCUTELNICUElena SCUTELNICU
Elena SCUTELNICU
This research focused on the investigation of the metallurgical behavior of the Al0.8CoCrFeNi high-entropy alloy and S235JR structural steel, welded with (Ni, Fe)-rich filler metal, by the Gas Tungsten Arc Welding (GTAW) method. The electric arc and the welding pool were protected against the contamination with gases from the environment, by employing high-purity Ar 4.8 inert gas that plays an important role in reducing the oxidation effects and the development of cracks in the weld and the adjacent areas. The microstructure and microhardness analysis did not reveal the existence of fragile phases, cracks, inadequate penetration, or other imperfections, showing an appropriate adhesion between the deposited metal and the substrates. At the interface between the Ni-rich weld metal and the high-entropy alloy, a higher hardness (448 HV0.2) than in the base material (358 HV0.2) was measured. Energy-dispersive X-ray analysis (EDS), performed at the interface between the weld metal and the base materials, did not show significant modifications of Co, Fe, and Cr percentages. However, during the investigation, significant variations in Al and Ni concentrations were observed, caused by the fast diffusion of chemical elements, and the development of hard (Ni, Al)-rich compounds. In some areas of the deposited metal, located at a distance of about 10 µm from the interface, the percentages of Ni and Al were higher than in the high-entropy alloy base material, being around 41% by weight Ni and over 13% by weight Al, while the concentrations of the Co, Cr, and Fe elements proportionally decreased (i.e., approximately 14% by weight Co, 12% by weight Cr, and 17% by weight Fe). The development of Ni3Al and NiAl compounds was also noticed, whose formation was determined by the local chemical concentration and the temperature reached in the vicinity of the diffusion zone. The XRD analysis showed a group of X-ray peaks in the Al0.8CrFeCoNi alloy that corresponded to both α-type—BCC and FCC phases. The crystallite size of the high-entropy alloy investigated was found to be 22.05 nm. Despite the diffusion phenomenon, if filler materials and process parameters are appropriately selected, quality joints of high-entropy alloys and structural steels can be carried out under good welding conditions.

6 November 2023 in Materials
Verified
Journal Article
Open access
PDF file
MCMukti Chaturvedi
Mukti Chaturvedi
ASArungalai Vendan S
Arungalai Vendan S
GSGeorge Simion
George Simion
CRCarmen Catalina Rusu
Carmen Catalina Rusu
Elena SCUTELNICUElena SCUTELNICU
Elena SCUTELNICU
Magnetically Impelled Arc Butt (MIAB) welding is a cutting-edge joining method that replaces the conventional welding procedures such as resistance, friction, flash and butt welding. It is a solid-state process that uses a rotating arc to heat up the butt ends of tubes, being followed by a forging process that completes the joining of the workpieces The magnetic flux density and the current interact to develop the Lorentz force that impels the arc along the faying surfaces. This process is found to produce high tensile strength and defect-free welds in ferrous materials and for this reason, it is predominantly employed in automobile applications for joining metallic tubes. Also, this joining procedure can be applied in the fabrication of boilers, heat exchangers, furnace piping in petrochemical industry and other safety-critical high-pressure machinery parts. The MIAB method has several advantages such as a shorter welding cycle, lower input energy requirement and lower loss of material. Compared to other solid-state welding processes, the MIAB welding has an important advantage in terms of cost-efficient welds with better control and reliability. Moreover, there are researchers who have investigated the joining of non-ferrous dissimilar materials using this welding procedure. The studies have been focused on process parametric analysis that involves optimizing and forecasting the magnetic field and thermal profile distribution. This review article provides competitive insights into various design features, computational methods, tests and material characterization, technical issues and workarounds, as well as automation aspects related to the MIAB-welding process. This work will prove to be a quick reference for researchers, useful to identify the research gaps and conflicting ideas that can be further explored for advancements in joining the similar and dissimilar materials.

13 November 2024 in Journal of Materials Research and Technology
Verified
Journal Article
Open access
GSGeorge Simion
George Simion
Julia C. Mirza-RoscaJulia C. Mirza-Rosca
Julia C. Mirza-Rosca
IVIonelia Voiculescu
Ionelia Voiculescu
Elena SCUTELNICUElena SCUTELNICU
Elena SCUTELNICU

31 December 2021 in Annals of Dunarea de Jos University of Galati. Fascicle XII, Welding Equipment and Technology
Verified
Journal Article
Open access
PDF file
Dan Catalin BirsanDan Catalin Birsan
Dan Catalin Birsan
GSGeorge Simion
George Simion
Ionelia VoiculescuIonelia Voiculescu
Ionelia Voiculescu
Elena SCUTELNICUElena SCUTELNICU
Elena SCUTELNICU
High entropy alloys are a new category of materials that contain at least four main chemical elements. One of the main advantages over the traditional alloys is the ability to maintain their properties at low or high temperatures. Researchers have investigated the possibility of welding these alloys so that they can be used in industrial applications. Good results have been obtained by welding butt joints of thin sheets, without the use of filler materials. In this paper it is investigated the possibility of welding overlap joints, with applications in the military field, of medium-thickness plates of AlCrFeMnNiHf0.05high entropy alloy on an Armox 500 steel support plate, using filler materials available on the market. The research focuses on the numerical simulation of three welding processes commonly used in on-site repair operations, namely manual metal arc, metal inert gas, and tungsten inert gas.

15 December 2022 in Annals of Dunarea de Jos University of Galati. Fascicle XII, Welding Equipment and Technology
Verified
Journal Article
Closed access
PDF file
Dan Catalin BirsanDan Catalin Birsan
Dan Catalin Birsan
GSGeorge Simion
George Simion
Resistance spot welding is a joining technique of two metal plates, employing pressure and heat. This welding process uses the metals’ electrical resistance to generate the heat that is needed to form the joints from similar or dissimilar metals. In the specialized literature, there are studies for different types of welding processes on the influence of using an interlayer material in both similar and dissimilar joints. In most of the cases, when the parameter optimisation was performed the results lead to an increase in the joint’s strength. In this paper, it is studied the resistance spot welding of 1mm thick E304 stainless steel sheets with and without a copper foil interlayer, using the same welding parameters for both cases. The tensile test of the joints showed a decrease in the resistance of the ones with copper foil interlayer and so, for this combination of materials, optimization of the welding parameters was performed using finite element analysis.