In Je Kang

Dr. In Je Kang

orcid

Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
10 October 2022 in IEEE Transactions on Plasma Science
Verified
Journal Article
Closed access
JYJong Keun Yang
Jong Keun Yang
CCChang Hyun Cho
Chang Hyun Cho
JKJi Hun Kim
Ji Hun Kim
DSDong Chan Seok
Dong Chan Seok
SYSeungryul Yoo
Seungryul Yoo
IKIn Je Kang
In Je Kang
The concept of a water surface plasma source (WSPS) was proposed to directly interact plasmas with water for large area water treatment, which is the type of volume dielectric barrier discharge (vDBD) with plate-to-plate. One electrode is submerged in water, while the other is floated in air, which is covered with a dielectric material. The characteristics of the WSPS were investigated by using a complementary metal–oxide–semiconductor (CMOS) camera, voltage and current probes, and optical emission spectroscopy (OES). The electrochemical parameters of plasma-activated water (PAW, 2 L) after plasma treatment times of 3 min by the WSPS were analyzed by using a multiparameter meter. As results, the formation of the water wave due to plasma generation, caused by the effect of the induced polarization forces, was observed at the WSPS. By comparison with the tap water, the applied voltage of the distilled water required higher than 130% for stable operation of the WSPS due to lower electrical conductivity (EC). As gap distance between dielectric plate and water surface increased, the applied voltage increased. In addition, an increase of 2 mm in the water level from the lower electrode required an approximately 5% increase in applied voltages for the ignition and stable plasma generation of the WSPS. The dominant peaks that were for N $_{2}$ species system in the spectrum of plasmas at the WSPS were analyzed by using the OES. In the case of distilled water, the pH values decreased from 6.25 to 4.24 and the EC increased from 2.00 to 22.33 $\mu $ S $\cdot$ cm by using multiparameter meter during plasma treatment, whereas in the case of tap water, the effects on the pH and EC were insignificant.

1 March 2017 in Current Applied Physics
Verified
Journal Article
Closed access
IKIn Je Kang
In Je Kang
MBM.-K. Bae
M.-K. Bae
TLT. Lho
T. Lho
KCK.-S. Chung
K.-S. Chung

8 April 2022 in Current Applied Physics
Verified
Journal Article
Closed access
IKIn Je Kang
In Je Kang
HCHyonu Chang
Hyonu Chang
YCYong-Sup Choi
Yong-Sup Choi
SJSoo Ouk Jang
Soo Ouk Jang
CCChang Hyun Cho
Chang Hyun Cho
HPHyunjae Park
Hyunjae Park

29 June 2021 in Nanomaterials
Verified
Journal Article
Open access
PDF file
IKIn Je Kang
In Je Kang
CCChang-Hyun Cho
Chang-Hyun Cho
HCHyonu Chang
Hyonu Chang
SJSoo-Ouk Jang
Soo-Ouk Jang
HPHyunjae Park
Hyunjae Park
JKJi Hun Kim
Ji Hun Kim
To validate the possibility of the developed microwave plasma source with a novel structure for plasma aerosol deposition, the characteristics of the plasma flow velocity generated from the microwave plasma source were investigated by a Mach probe with pressure variation. Simulation with the turbulent model was introduced to deduce calibration factor of the Mach probe and to compare experimental measurements for analyses of collisional plasma conditions. The results show calibration factor does not seem to be a constant parameter and highly dependent on the collision parameter. The measured plasma flow velocity, which witnessed fluctuations produced by a shock flow, was between 400 and 700 m/s. The optimized conditions for microwave plasma assisted aerosol deposition were derived by the results obtained from analyses of the parameters of microwave plasma jet. Under the optimized conditions, Y2O3 coatings deposited on an aluminum substrate were investigated using scanning electron microscope. The results presented in this study show the microwave plasma assisted aerosol deposition with the developed microwave plasma source is highly feasible for thick films with >50 μm.

2 December 2022 in Ceramics
Verified
Journal Article
Open access
PDF file
SJSoo-Ouk Jang
Soo-Ouk Jang
CCChanghyun Cho
Changhyun Cho
JKJi Hun Kim
Ji Hun Kim
IKIn Je Kang
In Je Kang
HCHyonu Chang
Hyonu Chang
HSHye Won Seok
Hye Won Seok
To improve plasma and chemical resistance on various vacuum components used for semiconductor manufacturing equipment, various ceramic coating techniques have been applied. Among these methods for ceramic coating, the well-known atmospheric plasma spray (APS) is advantageous for providing thick film (100 µm or more) deposition. However, there are problems associated with the phase transition of the coating film and poor film quality due to formation of voids. To solve these problems, the aerosol deposition (AD) method has been developed. This method provides nice ceramic film quality. However, the coating rate is quite slow and has difficulty producing thick films (>30 µm). To overcome these limitations, microwave plasma-assisted aerosol deposition (μ-PAD) is applied at low vacuum conditions without the AD nozzle. This method uses a microwave plasma source during the AD process. After enduring a long-term durability test, as a trial run, μ-PAD has been applied on the actual process site. With the Al2O3 powder, μ-PAD shows a coating rate that is 12 times higher than the AD method. In addition, the formation of a thicker film (96 µm) deposition has been demonstrated. On the other hand, the coating film hardness, porosity, adhesion, and withstand voltage characteristics were confirmed to be less than the AD method.

7 February 2025 in Journal of Vacuum Science & Technology A
Verified
Journal Article
Closed access
CCChang Hyun Cho
Chang Hyun Cho
JYJong Keun Yang
Jong Keun Yang
JKJi Hun Kim
Ji Hun Kim
DSDong Chan Seok
Dong Chan Seok
HYHyun Jong You
Hyun Jong You
IKIn Je Kang
In Je Kang
The effects of the addition of hydrogen on the properties of an argon plasma jet generated using a microwave plasma source under low-pressure conditions were experimentally investigated. Hydrogen was introduced at concentrations of 0.1%–1%, and the resulting changes in plasma jet characteristics were analyzed using optical emission spectroscopy (OES) and Langmuir probe (LP) measurements. The plasma jet length decreased significantly, and a reduction of over 60% occurred at a hydrogen concentration of 0.4% compared to that in pure argon plasma. The OES results indicated a reduction in Ar I intensities and a nonlinear trend in Hα and Hβ emission intensities. Based on LP measurements, decreases of 54% and 37% were observed in the electron temperature and plasma density, respectively, with 0.6% hydrogen addition. These effects are attributed to recombination reactions and interactions between argon and hydrogen species, which consume free electrons and metastable argon states.