For the analysis of the process of partial demagnetization of permanent magnets (PMs) in electric machines, a field model of coupled electromagnetic and thermal phenomena was proposed. In the proposed approach the non-linearity of the magnetic circuit, the effect of temperature on the magnetic, electrical and thermal properties of the materials as well as the developed method for modeling the process of partial demagnetization of the PMs were taken into account. In order to verify the usefulness and effectiveness of the developed algorithm as well as software for analyzing the impact of temperature and the process of partial demagnetization of the magnets on the operation of a PM motor, the results of calculations were compared with the results of experimental studies. The experimental tests were carried out on a specially designed and constructed measuring test stand. The results of the research on the process of partial demagnetization of magnets in the line start permanent magnet synchronous motor (LSPMSM) are presented and the conclusions resulting therefrom have been formulated.
The paper justifies the validity of analyzing the impact of temperature and the process of partial demagnetization of magnets on the operating parameters of machines. To analyze this impact, a field model of coupled electromagnetic and thermal phenomena in a permanent magnet synchronous motor was proposed. The non-linearity of the magnetic circuit, the effect of temperature on the magnetic, electrical and thermal properties of the materials as well as the developed method of modeling the process of partial demagnetization of the magnet were taken into account. Based on this model, an algorithm and software were developed to analyze the effect of temperature and the process of partial demagnetization of magnets on the work of the line start permanent magnet synchronous motor (LSPMSM). The elaborated software was used to study the effect of temperature during the motor starting phase on the magnetization state of the magnets after the start-up process. The calculation results were compared to the results of experimental studies. The experimental tests were carried out on a specially constructed test stand. The results of the research on the process of partial demagnetization of the magnets are presented and the conclusions resulting therefrom formulated.
The aim of this study was to investigate and analyze the impact of selected parameters during the tribocharging process of shredded poly(ethylene terephthalate) (PET) and high-density polyethylene (PE-HD) plastics on accumulated electric charge and electrostatic separation effectiveness. The accumulation of electric charge on surfaces of polymer particles as a result of their circular motion forced by the airflow cyclone container was investigated. The impact of the container material, time of tribocharging and the airflow intensity were experimentally examined. A container in which the particles of the considered polymers are electrified with opposite charges was selected. A high ability to accumulate surface charge on small particles of both polymers was demonstrated. The electrified mixed PET/PE-HD was subjected to a separation process. An electrostatic separator designed and constructed by the authors was used for to the separation. In turn, to assess the effectiveness of this separation, a dedicated vision system was used. Based on the result of the carried out tests, it has been assumed that the proposed approach’s effectiveness has been demonstrated by means of empirical validation.
The article deals with the results of a comparative analysis carried out on the construction of wind turbines applied in energy generation systems using the wind of passing vehicles. The structures of turbines with horizontal and vertical axes of rotation were considered. Vertical axis wind turbines (VAWTs) have been observed to operate in various wind directions, including highly turbulent winds. Therefore, for further experimental research, VAWTs have been selected, i.e., Darrieus and Savonius turbines and their modifications. For the purpose of experimental research, the authors developed and implemented their own laboratory setup. This setup enabled the measurement of quantities such as torque, power, and power coefficient and allowed for the determination of the start-up parameters of the investigated turbines. Moreover, as part of the research, wind speed was also measured in field conditions at a distance of 1 m from the expressway. The wind speed obtained from passing vehicles did not exceed 9 m/s. For this reason, the tests of the considered turbines using the experimental setup were performed for wind speeds in the range of 5.8–8.6 m/s. The investigations were conducted based on the obtained results, and it was concluded that the helical Savonius turbine possessed the highest efficiency (0.2047 from a wind speed of 5.8 m/s) in generating energy from the wind produced by vehicles traveling on roads.
The paper presents the Lorentz force and Maxwell stress formulas that give the same result of global force calculation for FE method. Edge element method (EEM) using vector potential A and nodal element method (NEM) using scalar potential Ω are considered. The formulas have been obtained from virtual work principle that has been adapted to the FE model. The FE network must be regular of homogenous element to obtain the equivalent formulas for EEM and equivalent formulas for NEM. The results of force calculation using the proposed methods have been compared with the analytical results. The systems with three cuboidal magnets and an induction motor with solid rotor described in TEAM Workshops Problem No. 30 were analyzed. Moreover, repulsive forces in the systems presented by TEAM Workshops Problem No. 7 and in the system with two ring-shaped magnets have been investigated.
2 December 2019 in Archives of Electrical Engineering
The paper presents an FE model of coupled electromagnetic and thermal phenomena in Line Start Permanent Magnet Synchronous Motors (LSPMSMs). An algorithm for solving equations of a discrete model using the FEM has been presented. On the basis of this algorithm the author’s personally developed software for the analysis of coupled electromagnetic-thermal phenomena in the LSPMS motors was elaborated. This software was used to analyze the start-up process of motors with identical stator and rotor magnetic circuits and different materials of the starting cage. The start-up process of motors with the squirrel-cage made of aluminum and copper was considered. The influence of temperature on the start-up process has been taken into account. The results of simulation tests were compared with the results of measurements.