The major construction and initial-phase operation of a second-generation gravitational-wave detector, KAGRA, has been completed. The entire 3 km detector is installed underground in a mine in order to be isolated from background seismic vibrations on the surface. This allows us to achieve a good sensitivity at low frequencies and high stability of the detector. Bare-bones equipment for the interferometer operation has been installed and the first test run was accomplished in March and April of 2016 with a rather simple configuration. The initial configuration of KAGRA is called iKAGRA. In this paper, we summarize the construction of KAGRA, including a study of the advantages and challenges of building an underground detector, and the operation of the iKAGRA interferometer together with the geophysics interferometer that has been constructed in the same tunnel.
We report on a quartz-enhanced photoacoustic sensor (QEPAS) based on a custom-made quartz tuning fork (QTF) to operate in both the fundamental and the first overtone vibrational mode resonances. The QTF fundamental mode resonance falls at ∼3 kHz and the first overtone at ∼18 kHz. Electrical tests showed that the first overtone provides a higher quality factor and increased piezoelectric current peak values, with respect to the fundamental flexural mode. To evaluate the QTF acousto-electric energy conversion efficiency, we operated the QEPAS in the near-IR and selected water vapor as the target gas. The first overtone resonance provides a QEPAS signal-to-noise ratio ∼5 times greater with respect to that measured for the fundamental mode. These results open the way to employing QTF overtone vibrational modes for QEPAS based trace gas sensing.
A detailed investigation of a set of custom quartz tuning forks (QTFs), operating in the fundamental and first overtone flexural modes is reported. Support losses are the dominant energy dissipation processes when the QTFs vibrate at the first overtone mode. These losses can be decreased by increasing the ratio between the prong length and its thickness. The QTFs were implemented in a quartz enhanced photoacoustic spectroscopy (QEPAS) based sensor operating in the near-IR spectral range and water vapor was selected as the gas target. QTF flexural modes having the highest quality factor exhibit the largest QEPAS signal, demonstrating that, by optimizing the QTF prongs sizes, overtone modes can provide a higher QEPAS sensor performance with respect to using the fundamental mode.
1 July 2024 in Journal of Cosmology and Astroparticle Physics
Monochromatic gamma-ray signals constitute a potential smoking gun signature for annihilating or decaying dark matter particles that could relatively easily be distinguished from astrophysical or instrumental backgrounds. We provide an updated assessment of the sensitivity of the Cherenkov Telescope Array (CTA) to such signals, based on observations of the Galactic centre region as well as of selected dwarf spheroidal galaxies. We find that current limits and detection prospects for dark matter masses above 300 GeV will be significantly improved, by up to an order of magnitude in the multi-TeV range. This demonstrates that CTA will set a new standard for gamma-ray astronomy also in this respect, as the world's largest and most sensitive high-energy gamma-ray observatory, in particular due to its exquisite energy resolution at TeV energies and the adopted observational strategy focussing on regions with large dark matter densities. Throughout our analysis, we use up-to-date instrument response functions, and we thoroughly model the effect of instrumental systematic uncertainties in our statistical treatment. We further present results for other potential signatures with sharp spectral features, e.g. box-shaped spectra, that would likewise very clearly point to a particle dark matter origin.
24 August 2014 in International Journal of Thermophysics
This paper is a review of analog front-end circuitry used in photoacoustic equipment with microphone or piezoelectric detection. A block structure of the front end as well as detailed circuit diagrams of preamplifiers dedicated for piezoelectric sensors and measurement condenser and electret microphones are described. The presented circuits are optimized toward low-noise operation. Practical remarks regarding the design of the remaining analog blocks are also given. The analysis shows that it is possible to design an analog front end for which specifications will be comparable with the best commercial solutions.
All the preamplifiers dedicated for Quartz Enhanced PhotoAcoustic Spectroscopy (QEPAS) applications that have so far been reported in the literature have been based on operational amplifiers working in transimpedance configurations. Taking into consideration that QEPAS sensors are based on quartz tuning forks, and that quartz has a relatively high voltage constant and relatively low charge constant, it seems that a transimpedance amplifier is not an optimal solution. This paper describes the design of a quartz QEPAS sensor preamplifier, implemented with voltage amplifier configuration. Discussion of an electrical model of the circuit and preliminary measurements are presented. Both theoretical analysis and experiments show that use of the voltage configuration allows for a substantial increase of the output signal in comparison to the transimpedance circuit with the same tuning fork working in identical conditions. Assuming that the sensitivity of the QEPAS technique depends directly on the properties of the preamplifier, use of the voltage amplifier configuration should result in an increase of QEPAS sensitivity by one to two orders of magnitude.