Zinc oxide (ZnO) nanowires (NWs) are excellent candidates for the fabrication of energy harvesters, mechanical sensors, and piezotronic and piezophototronic devices. In order to integrate ZnO NWs into flexible devices, low-temperature fabrication methods are required that do not damage the plastic substrate. To date, the deposition of patterned ceramic thin films on flexible substrates is a difficult task to perform under vacuum-free conditions. Printing methods to deposit functional thin films offer many advantages, such as a low cost, low temperature, high throughput, and patterning at the same stage of deposition. Among printing techniques, gravure-based techniques are among the most attractive due to their ability to produce high quality results at high speeds and perform deposition over a large area. In this paper, we explore gravure printing as a cost-effective high-quality method to deposit thin ZnO seed layers on flexible polymer substrates. For the first time, we show that by following a chemical bath deposition (CBD) process, ZnO nanowires may be grown over gravure-printed ZnO nanoparticle seed layers. Piezo-response force microscopy (PFM) reveals the presence of a homogeneous distribution of Zn-polar domains in the NWs, and, by use of the data, the piezoelectric coefficient is estimated to be close to 4 pm/V. The overall results demonstrate that gravure printing is an appropriate method to deposit seed layers at a low temperature and to undertake the direct fabrication of flexible piezoelectric transducers that are based on ZnO nanowires. This work opens the possibility of manufacturing completely vacuum-free solution-based flexible piezoelectric devices.

Polymeric nanostructured highly conductive films with Photonic Quasi Crystal topologies are presented with possibilities to open the path towards highly efficient white OLEDs.

In this paper two-dimensional (2D) photonic Thue–Morse quasicrystals (ThMo-PQCs) in active CdSe/CdS nanorod (NR) doped polymer nanocomposites are proposed and experimentally demonstrated. Active PQCs and undoped lattices have been prepared in a one-step fabrication process by an electron beam lithography technique (EBL) and the effects on light extraction and emission directionality are studied experimentally. Vertical extraction of light was found to be strongly dependent on both the geometric parameters of the ThMo-PQCs and the presence of NR dopants. By changing the geometrical parameters of the photonic structures, the resonance peak could be tuned from a narrow bluish green emission at 543 nm up to a red–NIR emission at 711 nm with a full width at half-maximum of 22 nm which is in good agreement with Bragg's diffraction theory and free photon band structure. Angular resolved measurements revealed a directional profile in the far-field distribution with guided mode extraction in both doped and undoped PQCs and an enhancement as high as 6.5-fold in light extraction was achieved in the doped photonic structures. These experimental results indicate the critical role of the CdSe/CdS NRs in improving the light extraction efficiency of 2D ThMo-PQCs for solid-state lighting and lasing.

Zinc oxide (ZnO) nanogenerators have attracted increasing interest in the scientific community for use in energy harvesting and mechanical sensing applications. Understanding the interplay between piezoelectricity and semiconductor physics is fundamental to enhancing these devices’ performances, although direct characterization at the nanoscale is challenging. With this work, we present a new strategy to improve piezoresponse force microscopy (PFM) measurements and analysis. This strategy was applied to study the piezoelectric performances of ZnO nanowires grown on seed layers deposited by gravure printing onto flexible substrates. We demonstrate the influence of nanowire diameter and atomic force microscope (AFM) tip position on the piezoresponse amplitude. We also explain our results with simulations showing the importance of considering semiconducting properties in the analysis.

Indoor farming of basil (Ocimum basilicum L.) under artificial lighting to support year-round produce demand is an area of increasing interest. Literature data indicate that diverse light regimes differently affect downstream metabolic pathways which influence basil growth, development and metabolism. In this study, basil was grown from seedlings to fully developed plants in a microcosm, an innovative device aimed at growing plants indoor as in natural conditions. Specifically, the effects of white (W) and blue-red (BR) light under a photosynthetic photon flux density of 255 μmol m⁻² s⁻¹ on plant growth, photochemistry, soluble nutrient concentration and secondary metabolism were investigated. Plants grew taller (41.8 ± 5.0 vs. 28.4 ± 2.5 cm) and produced greater biomass (150.3 ± 24.2/14.7 ± 2.0 g vs. 116.2 ± 28.3/12.3 ± 2.5 g fresh/dry biomass) under W light compared to BR light. The two lighting conditions differently influenced the soluble nutrient concentration and the translocation rate. No photosynthetic stress was observed under the two lighting regimes, but leaves grown under W light displayed higher levels of maximum quantum yield of PSII and electron transport rate. Sharp differences in metabolic patterns under the two lighting regimes were detected with higher concentrations of phenolic compounds under the BR light.

The efficiency of photomobile polymers (PMP) in the conversion of light into mechanical work plays a fundamental role in achieving cutting-edge innovation in the development of novel applications ranging from energy harvesting to sensor approaches. Because of their photochromic properties, azobenzene monomers have been shown to be an efficient material for the preparation of PMPs with appropriate photoresponsivity. Upon integration of the azobenzene molecules as moieties into a polymer, they act as an engine, allowing fast movements of up to 50 Hz. In this work we show a promising approach for integrating ZnO nanoparticles into a liquid crystalline polymer network. The addition of such nanoparticles allows the trapping of incoming light, which acts as diffusive points in the polymer matrix. We characterized the achieved nanocomposite material in terms of thermomechanical and optical properties and finally demonstrated that the doped PMP was better performing that the undoped PMP film.