Multichannel acquisition of ultrasonic guided waves can be used to extract dispersion curves, from the time-position domain (t-x) to the frequency-wavenumber (f-k), or frequency-velocity domain (f-c). Accurate measurements are needed in order to be able to precisely characterize the specimen, by improving the extraction of low amplitude modes and enhance resolution. The proposed method is based on the MUltiple SIgnal Classification algorithm combined with a multi-emitter and multi-receiver acquisition. In this work, this method is applied on experimental data to extract dispersive information from multilayered bonded specimens.
The reliability of NDE can be quantified by using the Probability of Detection (POD) approach. Former studies have shown the potential of the model-assisted POD (MAPOD) approach to replace expensive experimental determination of POD curves. In this paper, we make use of CIVA software to determine POD curves for a manual ultrasonic inspection of a heavy component, for which a whole experimental POD campaign was not available. The influential parameters were determined by expert analysis. The semi-analytical models used in CIVA for wave propagation and beam-defect interaction have been validated in the range of variation of the influential parameters by comparison with finite element modelling (Athena). The POD curves are computed for « hit/miss » and « â versus a » analysis. The verification of Berens hypothesis is evaluated by statistical tools. A sensitivity study is performed to measure the relative influence of parameters on the defect response amplitude variance, using the Sobol sensitivity index. A meta-model is also built to reduce computing cost and enhance the precision of estimated index.
In the context of an embedded structural health monitoring (SHM) system, two methods of transducer integration into the core of a laminate carbon fiber-reinforced polymer (CFRP) are tested: cut-out and between two plies. This study focuses on the effect of integration methods on Lamb wave generation. For this purpose, plates with an embedded lead zirconate titanate (PZT) transducer are cured in an autoclave. The embedded PZT insulation, integrity, and ability to generate Lamb waves are checked with electromechanical impedance, X-rays, and laser Doppler vibrometry (LDV) measurements. Lamb wave dispersion curves are computed by LDV using two-dimensional fast Fourier transform (Bi-FFT) to study the quasi-antisymmetric mode (qA0) excitability in generation with the embedded PZT in the frequency range of 30 to 200 kHz. The embedded PZT is able to generate Lamb waves, which validate the integration procedure. The first minimum frequency of the embedded PZT shifts to lower frequencies and its amplitude is reduced compared to a surface-mounted PZT.
Fiber Bragg Grating sensors record the ultrasonic signature of impacts on aeronautic composite structures. Experiments with 4 FBG sensors show proper localization of impacts with around 1cm precision using an algorithm based on time of arrivals of guided waves.
1 September 2023 in e-Journal of Nondestructive Testing
Ce travail s’inscrit dans le cadre du contrôle de composants de forte épaisseur, en particulier dans l’industrie nucléaire. Les conditions de fonctionnement sévères (température, pression, irradiation…) peuvent être à l’origine de divers t....
1 May 2008 in The Journal of the Acoustical Society of America
Ultrasonic array techniques are more and more used in NDT applications because of their flexibility and of their adaptability to complex configurations. In addition they can provide richer data than conventional methods. An optimal exploitation of such data in the aim of localizing and characterizing the detected flaws requires the application of imaging and reconstruction techniques based on a direct modeling of the propagation of ultrasound from the transmitter to the receiver. The quantitative models for the propagation which are available in the CIVA software platform developed at CEA‐LIST allow such direct modelling in parts of possibly complex geometries and materials. Different array data reconstruction methods based on the exploitation of these direct models have been studied and implemented in the plat‐form. Thus, in this communication we present in particular algorithms derived of synthetic focusing approach. These algorithms exploit the time of flight identification and can be apply to any set of array data. We also present a reconstruction method based on the post‐processing of the transfert matrix of the array and the application of MUSIC algorithm. We show and discuss results obtained with these methods both on simulated and experimental data.