NURUL NAZMIN ZULKARNAIN

Mrs. NURUL NAZMIN ZULKARNAIN


Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
11 February 2022 in Applied Sciences
Verified
Journal Article
Open access
PDF file
SRSiti Humairah Abd Rahman
Siti Humairah Abd Rahman
Syed Ahmad FarhanSyed Ahmad Farhan
Syed Ahmad Farhan
YSYon Azwa Sazali
Yon Azwa Sazali
LSLuqmanul Hakim Shafiee
Luqmanul Hakim Shafiee
Nadzhratul HusnaNadzhratul Husna
Nadzhratul Husna
MHMohd Firdaus Habarudin
Mohd Firdaus Habarudin
The present study aimed to investigate the effect of an expandable additive on the compressive strength and linear expansion of geopolymer cement, which is an alternative to ordinary Portland cement, for oil-well cementing. Fly-ash-based geopolymer cement samples, with the addition of slag cement as a strength enhancer, were prepared by using an elastomeric expandable additive (R-additive), which consists of styrene–butadiene rubber with a specific gravity of 0.945, at concentrations of 10%, 15%, 20% and 25% by weight of the solid blend, and cured in a water bath at 60 °C and atmospheric pressure, and a curing chamber at 90 °C and 3000 psi, or approximately 20.68 MPa. Mixability, amount of free water and slurry density were studied, and the effects of the concentration of R-additive on the compressive strength (F) and linear expansion (∆l/l0) of the samples were analyzed. When cured at 60 °C and atmospheric pressure, the highest F of 15.01 MPa was obtained when the concentration of R-additive was 10%, while the highest ∆l/l0 of 0.9985% was obtained when the concentration of R-additive was 25%. An increase in the curing temperature and pressure to 90 °C and 3000 psi (≈20.68 MPa) resulted in the reduction of F from 15.01 to 14.62 MPa and from 10.33 to 9.61 MPa, and the increase in ∆l/l0 from 0.52% to 0.63%, and from 0.99% to 1.32%, when the concentrations of R-additive were 10% and 25%, respectively. The findings suggest that the formulations adopted, which contain R-additive at concentrations ranging from 10% to 25%, fulfilled the requirements of the oil and gas industry.

29 January 2021 in Crystals
Verified
Journal Article
Open access
PDF file
SRSiti Humairah Abd Rahman
Siti Humairah Abd Rahman
NZNURUL NAZMIN ZULKARNAIN
NURUL NAZMIN ZULKARNAIN
Nasir ShafiqNasir Shafiq
Nasir Shafiq
This paper presents an experimental investigation on geopolymer cement formulations for enhancing oil-well integrity. Fresh slurry properties, mixability, density, free-water, and rheology were determined for possible field applications. The compressive strength and expansion characteristics were studied for the durability and integrity of the well system. Mix formulations complied with the requirements of API RP 10B-2. All formulations showed homogeneous mixability, rheological properties, the plastic viscosity (PV), and yield point (YP) were increased from 48 cP to 104 cP and 3.8 N/m2 12.4 N/m2, respectively, with the increase of the dosage of elastomeric type expandable material (R additive). The highest compressive strength of 15 MPa was obtained using 10% R additive in the mix-blend after 60 days of curing. Increasing the amount of R additive provides the optimum strength at 10.4 MPa with design 2, 3, and 4. The linear expansion was increased to about 1% at 60 days with 20% and 25% of the R additive dosage. Design of Experiment (DOE) was performed for setting three factors: curing time (A), curing temperature (B), and concentration of R additive (C) to optimize the linear expansion (response).

28 May 2021 in Sustainability
Verified
Journal Article
Open access
PDF file
NZNURUL NAZMIN ZULKARNAIN
NURUL NAZMIN ZULKARNAIN
Syed Ahmad FarhanSyed Ahmad Farhan
Syed Ahmad Farhan
YSYon Azwa Sazali
Yon Azwa Sazali
Nasir ShafiqNasir Shafiq
Nasir Shafiq
SRSiti Humairah Abd Rahman
Siti Humairah Abd Rahman
MHMohd Firdaus Habarudin
Mohd Firdaus Habarudin
Geopolymer cement (GPC) is an aluminosilicate-based binder that is cost-effective and eco-friendly, with high compressive strength and resistance to acid attack. It can prevent degradation when exposed to carbon dioxide by virtue of the low calcium content of the aluminosilicate source. The effect of the concentration of calcium chloride (CaCl2) as the accelerator on the compressive strength and acoustic impedance of GPC for well cement, while exposed to high pressure and high temperatures, is presented. Fly ash from the Tanjung Bin power plant, which is categorized as Class F fly ash according to ASTM C618-19, was selected as the aluminosilicate source for the GPC samples. Sodium hydroxide and sodium silicate were employed to activate the geopolymerization reaction of the aluminosilicate. Five samples with a density of 15 ppg were prepared with concentrations of CaCl2 that varied from 1% to 4% by weight of cement. Findings revealed that the addition of 1% CaCl2 is the optimum concentration for the curing conditions of 100 °C and 3000 psi for 48 h, which resulted in the highest compressive strength of the product. Results also indicate that GPC samples that contain CaCl2 have a smaller range of acoustic impedance compared to that of ordinary Portland cement.