Image analysis data obtained from scanning electron microscopy provided data for a detailed evaluation of the separation efficiency for various processes involving the beneficiation of particulate materials. A dry magnetic separation by a drum type magnetic separator served as a case study to visualize effects of processing of a skarn ore with a high content of cassiterite as ore mineral (~4 wt%). For this material, iron oxides and silicates are the main gangue mineral groups. Based on the obtained data, partition curves were generated with the help of local regression. From the partition curves, the separation efficiency was evaluated and the relevant particle properties deduced. A detailed analysis of the bias of the quantitative mineralogical data is presented. This bias was monitored and further analyzed in detail. Thorough analysis of feed and products of magnetic separation enabled identification of the most important factors that control losses of cassiterite to the magnetic product, namely the association with iron oxides and particle sizes below ~40 µm. The introduced methodology is a general approach applicable for the optimization of different separation processes and is not limited to the presented case study.

Better quality control for alloy manufacturing and sorting of post-consumer scraps relies heavily on the accurate determination of their chemical composition. In recent decades, analytical techniques, such as X-ray fluorescence spectroscopy (XRF), laser-induced breakdown spectroscopy (LIBS), and spark optical emission spectroscopy (spark-OES), found widespread use in the metal industry, though only a few studies were published about the comparison of these techniques for commercially available alloys. Hence, we conducted a study on the evaluation of four analytical techniques (energy-dispersive XRF, wavelength-dispersive XRF, LIBS, and spark-OES) for the determination of metal sample composition. It focuses on the quantitative analysis of nine commercial alloys, representing the three most important alloy classes: copper, aluminum, and steel. First, spark-OES is proven to serve as a validation technique in the use of certified alloy reference samples. Following an examination of the lateral homogeneity by XRF, the results of the techniques are compared, and reasons for deviations are discussed. Finally, a more general evaluation of each technique with its capabilities and limitations is given, taking operation-relevant parameters, such as measurement speed and calibration effort, into account. This study shall serve as a guide for the routine use of these methods in metal producing and recycling industries.

Slags from the metallurgical recycling process are an important source of resources classified as critical elements by the EU. One example is lithium from Li-ion battery recycling. In this context, the thermodynamic properties of the recycled component system play a significant role in the formation of the Li-bearing phases in the slag, in this case, LiAlO₂. LiAlO₂ crystal formation could be engineered and result in varying sizes and occurrences by different metallurgical processing conditions. This study uses pure ingredients to provide a synthetic model material which can be used to generate the valuable phase in the slag, or so-called engineered artificial minerals (EnAMs). The aim is to investigate the crystallisation of LiAlO₂ as an EnAM by controlling the cooling conditions of the model slag to optimise the EnAM formed during crystallisation. Characterisation of the EnAMs is an important step before further mechanically processing the material to recover the valuable element Li, the Li-bearing species, respectively. Investigations are conducted using powder X-ray diffraction (XRD), X-ray fluorescence (µXRF), and X-ray Computer Tomography (XCT) on two different artificial lithium slags from MnO-Al₂O₃-SiO₂-CaO systems with different cooling temperature gradients. The result shows the different EnAM morphology along the height of the slag, which is formed under different slag production conditions in a semi-pilot scale experiment of 5 kg. Based on the different EnAM morphologies, three defined qualities of the EnAM are identified: granular, dendritic, and irregular-shape EnAM.

The depletion of ore deposits, the increasing demand for raw materials, the need to process low-grade, complex and finely disseminated ores, and the reprocessing of tailings are challenges especially for froth flotation separation technologies. Even though they are capable of handling relatively fine grain sizes, the flotation separation of very fine and ultrafine particles faces many problems still. Further, the flotation of low-contrast semi-soluble salt-type minerals with very similar surface properties, many complex interactions between minerals, reagents and dissolved species often result in poor selectivity. This study investigates the flotation beneficiation of ultrafine magnesite rich in dolomite from desliming, currently reported to the tailings. The paper especially focuses on the impact of the depressant sodium hexametaphosphate (SHMP) on the following: (i) the froth properties using dynamic froth analysis (DFA), (ii) the separation between magnesite and dolomite/calcite, and (iii) its effect on the entrainment. As a depressant/dispersant, SHMP has a beneficial impact on the flotation separation between magnesite and dolomite. However, there is a trade-off between grade and recovery, and as well as the dewatering process which needs to be considered. When the SHMP increases from 200 g/t to 700 g/t, the magnesite grade increases from 67% to 77%, while recovery decreases massively, from 80% to 40%. The open circuit with four cleaning stages obtained a concentrate assaying 77.5% magnesite at a recovery of 45.5%. The dolomite content in the concentrate is about 20%, where 80% of dolomite was removed and importantly 98% of the quartz was removed, with only 0.3% of the quartz in the final concentrate. Furthermore, the application of 1-hydroxyethylene-1,1-diphosphonic acid (HEDP) as a more environmentally friendly and low-cost alternative to SHMP is presented and discussed. Using only 350 g/t of HEDP can achieve a similar grade (76.3%), like 700 g/t of SHMP (76.9%), while obtaining a 17% higher magnesite recovery as compared to 700 g/t of SHMP. Interestingly, the proportion of hydrophilic quartz minerals ending up in the concentrate is lower for HEDP, with only 1.9% quartz at a recovery of 21.5% compared to the 2.7% of quartz at a recovery of 24.9% when using SHMP. The paper contributes in general to understanding the complexity of the depressant responses in froth flotation.

With the increasing demand for metalliferous and mineral raw materials and the consequent depletion of the global natural resource base, the possible utilization of secondary raw material sources is receiving more and more attention. In the present study, we present results from a detailed vanadium deportment study of three basic oxygen furnace slag (BOS) samples known to containing elevated bulk concentrations of vanadium. Complementary analytical methods that were used to quantify the abundance and composition of V-containing phases include SEM-based automated mineralogy, X-ray fluorescence analysis, and X-ray powder diffraction as well as electron probe microanalysis. The vanadium deportment was quantified using Monte-Carlo simulations of the data obtained from automated mineralogy and electron microprobe analysis. The total V concentrations identified by XRF are between 1.7 and 2.2 wt.% V. The most important hosts of vanadium are larnite-, brownmillerite- and portlandite-solid solutions. In two samples Ca carbonates also significantly contribute to the V deportment, while wuestite, lime, and native iron do not contribute significantly to the vanadium deportment. A thorough consistency check identifies considerable uncertainties in the density of the V-bearing phases as the most likely reason to explain remaining discrepancies between measured and calculated V values.