Supercavitation is one of the most attractive technologies to achieve high speed for underwater vehicles. However, the multiphase flow with high-speed around the supercavitating vehicle (SCV) is difficult to simulate accurately. In this paper, we use modified the turbulent viscosity formula in the Standard K-Epsilon (SKE) turbulent model to simulate the supercavitating flow. The numerical results of flow over several typical cavitators are in agreement with the experimental data and theoretical prediction. In the last part, a flying SCV was studied by unsteady numerical simulation. The selected computation setup corresponds to an outdoor supercavitating experiment. Only very limited experimental data was recorded due to the difficulties under the circumstance of high-speed underwater condition. However, the numerical simulation recovers the whole scenario, the results are qualitatively reasonable by comparing to the experimental observations. The drag reduction capacity of supercavitation is evaluated by comparing with a moving vehicle launching at the same speed but without supercavitation. The results show that the supercavitation reduces the drag of the vehicle dramatically
Drag reduction has constantly received great attention due to its extensive range of applications in fluid transportation and vehicle industries. The vital role of two different additive and non‐additive techniques (polymer additives and superhydrophobic surfaces) to reduce the drag force experienced by underwater vehicles, fluid flow through pipes, ducts, open or closed channels, and other wall‐bounded laminar and turbulent flows is highlighted. Reducing the drag resistance can significantly enhance the performance of immersed vehicles and results in saving the energy consumed on a large scale. The progress in theoretical modeling, experimental and computational studies of both techniques are reviewed, together with the surface design, wettability, and influence of the roughness factor of superhydrophobic surfaces and the effect of polymer drag‐reducing agents for wall‐bounded flows and multiphase flows. General formulations, potential applications, and major issues involved in the aforementioned approaches are summarized.
The properties of asymmetric wake patterns behind a flat plate inclined at angles of attack 20°, 25°, and 30° are investigated. The Reynolds number based on the inflow velocity and the plate width is 1000. Both two-dimensional and three-dimensional calculations are performed by direct numerical simulations. Compared to the three-dimensional simulations, the two-dimensional calculations predict a significantly lower pressure on the rear surface of the plate, which consequently leads to very high drag and lift forces on the plate. The asymmetric mean wake flow, turbulence properties, and coherent patterns in the three-dimensional simulations are analysed by time- and phase-averaged techniques. Unlike the symmetric wake flow, the vortices shed from the leading and trailing edges of an inclined plate possess unequal strength with the trailing edge vortex having higher strength. It is observed that the present three-dimensional simulations predict results which compare well with the experimental data. In addition, wake instabilities in the form of oblique modes and vortex dislocations are observed in the 20° angle of attack case. It is found that this intrinsic instability is most likely due to the low incidence angle rather than the prevailing low Reynolds numbers.
Phase change material (PCM) is one of the most important ways to store and manage energy. The melting process of PCM in a rectangular enclosure with the different aspect ratio is frequently related to some thermal energy storage devices. In this work, the melting of PCM in the horizontal rectangular enclosures heated from the different sides and the influence of aspect ratio of the rectangle are carefully studied. The enthalpy porosity technique and the finite volume method (FVM) are used to simulate the melting process numerically. The results show that the melting process of PCM can be dominated by conduction or natural convection due to the different heated sides. The melting of PCM in the enclosure heated from the bottom side is firstly affected by conduction and then mostly influenced by convection. In addition, the aspect ratio of the rectangular enclosure is found to play an important role in the melting process. Finally, a series of fitting correlations of the liquid fraction, Nusselt number and the energy storage are presented with the influence of aspect ratios in order to provide the reference for designing the rectangular container of PCM. This study is helpful for the selection of an appropriate aspect ratio and heating method to achieve the desired energy storage performance of encapsulated PCM.
Honeycomb structure with phase change material (PCM) is frequently used in passive thermal management devices. The geometrical shape of the honeycomb core greatly influences the melting rate of the PCM. This paper investigates the melting rates of PCM in honeycomb cores of non-hexagonal cells in comparison with that of hexagonal cell in three Rayleigh numbers. The objective is to find the optimal shape in order to reduce the melting time of the PCM. The constrained melting behaviors of PCM in triangular, quadrilateral, hexagonal, and circular honeycomb cores are numerically studied. The enthalpy porosity technique and finite volume method are used in this paper. The instantaneous liquid fraction and energy absorption of PCM in different honeycomb cores are discussed in detail. The influences of the placed orientation and aspect ratio of different cores on melting rates of PCM are considered. Results show that the melting rate of PCM in a rectangular core is always higher than the hexagonal core for the given aspect ratio and Rayleigh number. The geometrical factor (GF), which indicates the cross-sectional area per unit perimeter, is found to be an important index on the melting rate. At a small Rayleigh number, it takes a longer melting time of the PCM for the core with a larger GF. As the Rayleigh number is large, the melting time of the PCM is affected by both the GF and the orientation of the cores.
Flows of dilute polymer solutions past a hydrofoil (NACA0012) are examined by direct numerical simulation to investigate the modification of the wake pattern due to the addition of polymer. The influence of polymer additive is modeled by the FENE-P model in order to simulate a non-linear modulus of elasticity and a finite extendibility of the polymer macromolecules. Simulations were carried out at a Reynolds number of 1000 with the angle of attack varying from 0° to 20°. The results show that the influence of polymer on the flow behavior of the flow past a hydrofoil exhibits different flow regimes. In general, the addition of polymer modifies the wake patterns for all angles of attack in this study. Consequently, both drag and lift forces are changed as the Weissenberg number increases while the drag of the hydrofoil is enhanced at small angles of attack and reduced at large angles of attack. As the Weissenberg number increases, two attached recirculation bubbles or two columns of shedding vortices downstream tend to be symmetric, and the polymer tends to make the flow less sensitive to the variation of the angle of attack.