Advances in micro- and nanotechnology have led to rapid employment of spintronic sensors in both recording and non-recording applications. These state-of-the-art magnetoresistive spintronic sensors exhibit high sensitivities and ultra-low field detectivities that meet requirements of smart sensing applications in the fields of internet of things, mobile devices, space technology, aeronautics, magnetic flux leakage, domotics, the environment, and healthcare. Moreover, their ability to be customized and miniaturized, ease of integration, and cost-effective nature make these sensors uniquely competitive with regard to mass production. In this study, we discuss magnetoresistive field sensors based on the planar-Hall effect, which are very promising for their high sensitivity and sensing ultra-low magnetic fields. We provide a detailed historical overview and discuss recent dramatic developments in several application fields. In addition, we discuss sensor material property requirements, design architectures, noise-reduction techniques, and sensing capabilities, along with the high repeatabilities and good flexibility characteristics of such devices. All of these high-performance characteristics apply across a wide temperature range and make the sensor robust when used in various novel applications. The sensor also appears promising because it is cost-effective and can be used in micro-sensing applications. Recently, a noteworthy study that combined integrated planar-Hall magnetoresistive sensors with microfluidic channels revealed their potential for highly localized magnetic field sensing. This characteristic makes them suitable for point-of-care-technologies that require resolutions of a few pT at room temperature.
High thermal stability of planar Hall resistance (PHR) signal in magnetic sensors, configured as a cross-junction and as a Wheatstone bridge, has been demonstrated. A thermal drift of PHR signal, being proportional to PHR offset at zero field, is few orders of magnitude less than the thermal drift of anisotropic magnetoresistance signal. The thermal drift of PHR originates from two independent components, base line drift and signal amplitude drift. The temperature coefficient of base line drift, normalized by zero field offset, is similar with the temperature coefficient of resistance. This makes possible to characterize a drift at any temperature range, by a single measurement of PHR under ambient conditions. A signal amplitude drift is shown to be dependent on sensor's geometry, and becomes higher with a reduction of the width of a current path. The temperature coefficients of base line drift and signal amplitude drift are of opposite signs. A possibility of mutual compensation of signal amplitude drift and base line drift by a slight misbalancing of a bridge-type sensor has been demonstrated.
Advanced microelectromechanical system (MEMS) magnetic field sensor applications demand ultra-high detectivity down to the low magnetic fields. To enhance the detection limit of the magnetic sensor, a resistance compensator integrated self-balanced bridge type sensor was devised for low-frequency noise reduction in the frequency range of 0.5 Hz to 200 Hz. The self-balanced bridge sensor was a NiFe (10 nm)/IrMn (10 nm) bilayer structure in the framework of planar Hall magnetoresistance (PHMR) technology. The proposed resistance compensator integrated with a self-bridge sensor architecture presented a compact and cheaper alternative to marketable MEMS MR sensors, adjusting the offset voltage compensation at the wafer level, and led to substantial improvement in the sensor noise level. Moreover, the sensor noise components of electronic and magnetic origin were identified by measuring the sensor noise spectral density as a function of temperature and operating power. The lowest achievable noise in this device architecture was estimated at ~3.34 at 100 Hz.
A set of Planar Hall Resistance (PHR) sensors has been fabricated on rigid and flexible substrates. High signal-to-noise ratio, low offset voltage, nearly zero hysteresis of signal and excellent linearity has been demonstrated for sensors, based on Ta (5 nm)/NiFe (10 nm)/IrMn (10 nm)/Ta (5 nm) thin films, grown on PDMS and Parylene C polymeric substrates. Effect of bending on the performance of the PHR sensors has been studied. The effect of bending deformation on the performance characteristics of the fabricated PHR sensors is reversible until the bending angle reaches a critical one. The critical bending angle is shown to be dependent on the substrate composition. An irreversible deformation of sensor's film, accompanied by the formation of wrinkles and cracks, occurs when the bending angle exceeds the critical one. This deformation originates from the difference between the values of Young's modulus of the substrate and the film. The bending stability of PHR sensor, grown on PDMS substrate, has been improved by deposition of 1 μm of Parylene C both as a buffer and as a capping layer. The performance characteristics of the designed shapeable PHR sensors are compatible with requirements for applications in wearable electronics and medical diagnostic devices.
The resolution of planar-Hall magnetoresistive (PHMR) sensors was investigated in the frequency range from 0.5 Hz to 200 Hz in terms of its sensitivity, average noise level, and detectivity. Analysis of the sensor sensitivity and voltage noise response was performed by varying operational parameters such as sensor geometrical architectures, sensor configurations, sensing currents, and temperature. All the measurements of PHMR sensors were carried out under both constant current (CC) and constant voltage (CV) modes. In the present study, Barkhausen noise was revealed in 1/f noise component and found less significant in the PHMR sensor configuration. Under measured noise spectral density at optimized conditions, the best magnetic field detectivity was achieved better than 550 pT/√Hz at 100 Hz and close to 1.1 nT/√Hz at 10 Hz for a tri-layer multi-ring PHMR sensor in an unshielded environment. Furthermore, the promising feasibility and possible routes for further improvement of the sensor resolution are discussed.