A method to obtain the effective thermal conductivity due to radiation heat transfer, which occurs in steel bar bundles during their heating associated with heat treatment, is presented. This problem is related to the determination of the thermal properties of a bar bundle, which is modeled as a porous medium with a granular structure. The thermal properties of the bundles are needed to optimize the heat treatment process. A methodology for radiation heat transfer modeling that uses radiation resistance is presented. Resistance is calculated from the radiosity balance for the surfaces that form the analyzed system. The geometry of the heat transfer area is defined using the elementary cell concept. The analysis of the phenomenon is performed within the temperature range from 200 to 700°C. The values of radiation resistance for three different unit cells are presented, as well as the values of the associated effective thermal conductivities due to radiation . The cell radiation resistance decreases sharply with temperature, with the values between 0.08 and for the temperature range studied. The coefficient increases with bar diameter, and for bar bundles of 10 and 40 mm, its maximal values are 1.21 and 4.34 , respectively. Finally, the values of radiation exchange factor for the medium were analyzed. decreases slightly with emissivity and bar diameter, ranging from 0.61 to 0.41.
The paper presents a computational model used for the analysis of complex heat flow in the area of steel rectangular sections. The model is based on the analysis of heat resistance. A section is considered in the study as a two-phase system of steel and air. Calculation of total section resistance Rst takes into consideration heat conduction in individual phases, thermal radiation between internal section surfaces and free convection of the gaseous phase. Calculations are performed within the temperature range from 20 to 700°C. The results obtained in the study were presented using the replacement thermal conductivity of the section krp. Calculations were performed for three types of sections: 20×40, 40×40 and 60×60mm with different wall thickness. The values obtained for kef ranged from 3÷13 W/(m·K). The model also allows for the qualitative analysis of heat flow. This analysis is connected with determination of the quantitative fraction of specific heat transfer mechanisms which occur in global heat flow
The article describes the results of numerical analyses and traditional calculations of the heat transfer coefficient in ceilings with a complex cross-section, and with materials of varying density built-in inside the cross-section. Prefabricated prestressed reinforced concrete, composite reinforced, and ribbed reinforced concrete ceilings were analyzed. Traditional calculations were carried out in accordance with the EN ISO 6946:2017 standard, while the numerical analyses were carried out in a program based on the finite element method (FEM). It has been shown that calculations can be a good alternative to nondestructive testing (NDT) and laboratory tests, whose use in the case of ceilings with different geometries is limited. The differences between the calculations carried out in accordance with EN ISO 6946:2017, and the results of numerical analyses are 12%–39%. The way the air voids are taken into account has an impact on the calculation results. In the traditional method, an equivalent thermal conductivity coefficient was used, while in the numerical analysis, the coefficient was selected from the program’s material database. Since traditional calculations require simplifications, numerical methods should be considered to give more accurate results.
In many cases of heat treatment of steel products, the heated charge has a porous structure. The examples of such charges include bundles of long steel components e.g., bars. The basic thermal property of the charge in this form is effective thermal conductivity kef. This paper presents the results of experimental examinations of effective thermal conductivity of the porous charge, which is composed from various types of steel long components. Due to the specific nature of the samples, a special measurement stand was constructed based on the design of a guarded hot plate apparatus. The measurements were performed for sixteen different samples across a temperature range of 70–640 °C. The porosity of the samples, depending on the type of components used, ranged from 0.03 to 0.85. Depending on these factors, the effective thermal conductivity ranged from 1.75 to 8.19 W·m−1·K−1. This accounts for 0.03 to 0.25 of the value of thermal conductivity of the solid phase of the charge, which in the described cases was low-carbon steel. It was found that the effective thermal conductivity rises linearly with temperature. The intensity of this increase and the value of coefficient kef depend on the transverse dimension of the components that form the charge. The results may represent the basis for the validation of various models of effective thermal conductivity with respect to the evaluation of thermal properties of the porous charge.
Purpose: This paper aims to considered the problem of identification of temperature-dependent thermal conductivity in the nonstationary, nonlinear heat equation. To describe the heat transfer in the furnace charge occupied by a homogeneous porous material, the heat equation is formulated. The inverse problem consists in finding the heat conductivity parameter, which depends on the temperature, from the measurements of the temperature in fixed points of the material. Design/methodology/approach: A numerical method based on the finite-difference scheme and the least squares approach for numerical solution of the direct and inverse problems has been recently developed. Findings: The influence of different numerical scheme parameters on the accuracy of the identified conductivity coefficient is studied. The results of the experiment carried out on real measurements are presented. Their results confirm the ones obtained earlier by using other methods. Originality/value: Novelty is in a new, easy way to identify thermal conductivity by known temperature measurements. This method is based on special finite-difference scheme, which gives a resolvable system of algebraic equations. The results sensitivity on changes in the method parameters was studies. The algorithms of identification in the case of a purely mathematical experiment and in the case of real measurements, their differences and the practical details are presented.