Even though the rules for the free circulation of machinery within the European Union (EU) market have existed for more than 30 years, accidents related to their activities have constantly been reaching significant value. When designing a machine, the design must stem from a risk assessment, where all stages of its life cycle and the ways to use it must be taken into consideration. In industrial operations with old machinery, despite fulfilling its function reliably, the safety level is below the developing requirements for safe operations. The proposed methodology to assess machinery safety conditions comes from the assumption of the proper application of risk assessment steps and their effectiveness in risk reduction mainly through implementing both effective and efficient preventive measures. The objective of the research applied in three operations was to verify the methods concerning machinery safety and its management. The created methodology, based on 19 requirements for safety, evaluates the level of current measures using a criterion of the current safety status and the total effectiveness of safety measures. Its output is the assessment of the efficiency level of the implemented safety measures of each machine as well as of the whole operation.

Low-frequency noise, the frequency range from approximately 10 Hz to 200 Hz, has been recognized as a special environmental noise problem. The World Health Organization recognizes the special place of low-frequency noise as an environmental problem. Noise can damage hearing, and it affects the whole body. Low-frequency sound is heard by humans, but infrasound is not audible. Low-frequency sound is most often measured based on a weighting function of the frequency. The A-weighted level underestimates the effects of low-frequency noise. For the detrimental effects of low-frequency sound, it would be appropriate to apply measurements using Z-weighting. The aim of this paper was to propose a comprehensive method of acoustic risk assessment (CMARA) that implements the effects of low-frequency values of noise exposure. The proposed methodology has been applied in practice at four workplaces for seven work activities. A risk assessment using the proposed CMARA method for individual activities shows that the noise exposure time may pose a health risk in the occupational and environmental process due to exposure to low-frequency noise at the limit of audibility. A high risk was assessed for activities WA2 (machining) and WA3 (spot welding). This paper highlights the need to measure low-frequency noise using Z-filter weighting.

Fire is defined as an extremely hazardous event, causing a threat to life and health of persons, but also damage to the economic sphere. It has been shown many times that fire can occur anywhere and at any time. In order to minimize the risk of fire manifestations, it is necessary to understand its course. In technical practice, computational models are used to determine the partial manifestations of fire, such as fire spread rate, smoke generation rate in the burning area, formation of toxic burning products, flame height, and others. One of the important characteristics is also the energy balance in the burning area relating to the character of burning material, access of oxygen necessary for exothermic reaction of burning, and reaction of the installed safety devices. In this paper we will point out the fire safety of the building. The FDS (Fire Dynamics Simulator) model is recently used in practice, and its advantage is the possibility to model fire even in large and atypical spaces. The contribution of this paper is the practical application of fire safety of construction using the FDS Model, to reduce the cost of fire safety for the structure being constructed. Attention was paid to evaluating how the heat energy that is released during a fire can be influenced by the installed stable fire-extinguishing equipment, taking into consideration the fire resistance of the building structures.

The purpose of this article is to determine the environmental impacts of underground gasification on the population and to analyze the risk of underground coal gasification (UCG) activities using selected risk assessment methods. Coal gas is a regular part of coal deposits and its extraction also allows the use of coal deposits that cannot be extracted by traditional methods. These technologies bring both positive and negative aspects. The paper points out the risk analysis, hazard identification and assessment during the operation of UCG technology using a risk graph and a risk matrix. Identified risks to workers that cannot be reduced should be taken into consideration and appropriate safeguard should be used. For each risk, it is necessary to inform employees about regular education and training. From worldwide experience with this technology, it is possible to analyze risks in Slovakia. Actual gasification produces polluting gases such as carbon dioxide, carbon monoxide, hydrogen sulphide, hydrogen sulphide, nitrogen oxides, tar and ash, and creates a risk that may occur on and under the surface of the site depending on the geological and hydrogeological structure of the deposits. Possible measures to mitigate the adverse effects are proposed for the implementation of this technology. Coal is still one of the main domestic primary energy sources. Currently, only 5 out of 19 deposits in the Slovak Republic are used. Underground gasification could increase the use of Slovak coal and brown coal deposits.

Results obtained from measuring the required amount of steel abrasive material with various fragmentations, which is transported by a special kind of scraper conveyor, offers information that is useful for operators of the abrasive blast cabinets. The presented article describes an innovative methodology developed for determination of the most relevant operational parameters relating to the above-mentioned situation. The most important parameters in this case are: the optimal amount of the abrasive material, the conveying speed of the scraper conveyor and the feeding of the conveyor with regard to partial or full elimination of instable operational area. Elimination of the instable operational area is possible by means of a simple constructional modification of the given conveying system according to the results obtained from experimental investigation, which was performed using special, originally developed laboratory testing equipment.

Firefighters are regularly exposed to risk of injuries as a result of their intervention activities connected with hazards from fire and explosion, as well as due to carrying heavy personal working equipment and injured victims from accidents. Another hazardous factor is working under unfavorable weather conditions and also moving on slippery or bumpy surfaces. Employers provide personal protective work equipment to employees if a hazard cannot be eliminated or reduced by technical means, such as means of collective protection or methods and forms of work organization. Personal Protective Equipment (PPE) should provide effective protection against existing and foreseeable hazards and should not in itself create a greater risk. It should be adapted to the existing and predictable working conditions and working environment at the work site, meet the criteria of ergonomics and the health condition of an employee as well as be suitable and adapted to the wearer’s body so that, if possible, there is no risk of harm to the employee’s health. The aim of this Special Issue is to explore the limits of sustainable implementation of additive technologies within current manufacturing practices and current requirements for personal protective equipment for firefighters. More precisely, the goal of this special article is to show new ideas in firefighting footwear such as a quick donning and doffing system as well as various other improvements and sustainable design of firefighting footwear. The aim is to present new ideas and concepts, the latest advances, and technical tools supporting the sustainable use of protective firefighting footwear. Special attention will be paid to standards that ensure the highest standard and quality.