Escola d’Enginyeria de Barcelona Est, Mechanical Engineering Department, Universitat Politècnica de Catalunya, Av. Eduard Maristany, 10-14, 08019 Barcelona, Spain
Dr. Moahmmad Damous Zandi
Escola d’Enginyeria de Barcelona Est, Mechanical Engineering Department, Universitat Politècnica de Catalunya, Av. Eduard Maristany, 10-14, 08019 Barcelona, Spain
This paper aims to determine the flexural stiffness and strength of a composite made of a polylactic acid reinforced with wood particles, named commercially as Timberfill, manufactured through fused filament fabrication (FFF). The influence of four factors (layer height, nozzle diameter, fill density, and printing velocity) is studied through an L27Taguchi orthogonal array. The response variables used as output results for an analysis of variance are obtained from a set of four-point bending tests. Results show that the layer height is the most influential parameter on flexural strength, followed by nozzle diameter and infill density, whereas the printing velocity has no significant influence. Ultimately, an optimal parameter set that maximizes the material’s flexural strength is found by combining a 0.2-mm layer height, 0.7-mm nozzle diameter, 75% fill density, and 35-mm/s velocity. The highest flexural resistance achieved experimentally is 47.26 MPa. The statistical results are supported with microscopic photographs of fracture sections, and validated by comparing them with previous studies performed on non-reinforced PLA material, proving that the introduction of wood fibers in PLA matrix reduces the resistance of raw PLA by hindering the cohesion between filaments and generating voids inside it. Lastly, five solid Timberfill specimens manufactured by injection molding were also tested to compare their strength with the additive manufactured samples. Results prove that treating the wood-PLA through additive manufacturing results in an improvement of its resistance and elastic properties, being the Young’s module almost 25% lower than the injected material.
Additive manufacturing (AM) or 3D printing offers a new paradigm for designing and developing chemical reactors, in particular, prototypes. The use of 3D printers has been increasing, their performance has been improving, and their price has been reducing. While the general trend is clear, particular applications need to be assessed for their practicality. This study develops and follows a systematic approach to the prototyping of Advanced Oxidation Processes (AOP) reactors. Specifically, this work evaluates and discusses different printable materials in terms of mechanical and chemical resistance to photo-Fenton reactants. Metallic and ceramic materials are shown to be impracticable due to their high printing cost. Polymeric and composite materials are sieved according to criteria such as biodegradability, chemical, thermal, and mechanical resistance. Finally, 3D-printed prototypes are produced and tested in terms of leakage and resistance to the photo-Fenton reacting environment. Polylactic acid (PLA) and wood–PLA composite (Timberfill®) were selected, and lab-scale raceway pond reactors (RPR) were printed accordingly. They were next exposed to /Fe(II) solutions at pH = 3 ± 0.2 and UV radiation. After 48 h reaction tests, results revealed that the Timberfill® reactor produced higher Total Organic Carbon (TOC) concentrations (9.6 mg·L−1) than that obtained for the PLA reactor (5.5 mg·L−1) and Pyrex® reactor (5.2 mg·L−1), which suggests the interference of Timberfill® with the reaction. The work also considers and discusses further chemical and mechanical criteria that also favor PLA for 3D-printing Fenton and photo-Fenton reactors. Finally, the work also provides a detailed explanation of the printing parameters used and guidelines for preparing prototypes.
This paper deals with the improvement of the material surface state of friction stir welding paths modified in situ by plastic deformation through ball burnishing. The metallurgical and topological states of materials joined by this welding technique are typically detrimental to the ulterior performance of the workpiece, and it is believed that ball burnishing can improve these states to enhance functioning. This study is divided into two phases. The first one is experimental and consists of welding aluminum AA2024-T3 plates while combining different tool rotations and welding speeds. Then, the welding line is deformed locally by ball burnishing. The improvement of the topology and deep hardness distribution is measured and discussed, and the evolution of mechanical properties is assessed through tensile tests. The second phase is oriented towards estimating the residual stresses by combining two pre-existing models of friction stir welding and burnishing developed by the same authors using ANSYS®. Friction stir welding experimentation and measurements show a decrease in the values of all measured mechanical properties compared to the original material. The dominant factor affecting the properties and texture of the materials is the rotational speed of the tool, with the rupture point in the tensile test located in the distinct zone with the lowest value of microhardness on the advancing side. The higher the ratio of the rotational speed to the welding speed, the lower the roughness value. Finally, ball burnishing is proven to be an effective method to enhance the surface integrity of friction stir welded joints in light of the results, achieving a reduction of 11% to 36% in average roughness and an increase of about 22% in hardness profile, along with an integrated numerical model estimation of a remarkable effect on compressive residual stresses in-depth on the retreating side of the welded samples. However, in some tests, this treatment reduced some characteristics (yield stress and failure strain).