High temperature and overheating of photovoltaic panels lead to efficiency losses and eventual degradation. For solar PV systems, this is a significant impediment for achieving economic viability. In this study, a novel Window-Integrated Concentrated Photovoltaic (WICPV) system is proposed for window integration. This offers high (50%) transparency and is fabricated and characterised indoors at an irradiance of 1000 Wm−2. Its electrical performance is tested (a) without applied cooling (i.e., under natural ventilation) and (b) with a heat sink to accommodate passive cooling media. The results are compared to study the effects of reduction in operating temperature on system performances. The effectiveness of a sensible cooling medium (water) and two latent heat removal media, phase change materials (or PCMs, RT50 and RT28HC), is investigated. This paper reports the passive temperature regulation of this WICPV at ambient testing conditions. The results demonstrate an increase in electrical power output by (i) 17% (RT28HC), (ii) 19% (RT50), and (iii) 25 % (circulating water) compared with the naturally ventilated system. This shows that PCMs are considerably useful for thermal regulation of the WICPV. Any improvement in efficiencies will be beneficial for increasing electrical energy generation and reducing peak energy demands.
This paper investigates the potential of a new integrated solar concentrated photovoltaic (CPV) system that uses a solo point focus Fresnel lens for multiple multi-junction solar cells (MJSCs). The proposed system comprises of an FL concentrator as the primary optical element, a multi-leg homogeniser as the secondary optical element (SOE), a plano-concave lens, and four MJSCs. A three-dimensional model of this system was developed using the ray tracing method to predict the influence of aperture width, height, and position with respect to MJSCs of different reflective and refractive SOE on the overall optical efficiency of the system and the irradiance uniformity achieved on the MJSCs’ surfaces. The results show that the refractive homogeniser using N-BK7 glass can achieve higher optical efficiency (79%) compared to the reflective homogeniser (57.5%). In addition, the peak to average ratio of illumination at MJSCs for the reflective homogeniser ranges from 1.07 to 1.14, while for the refractive homogeniser, it ranges from 1.06 to 1.34, causing minimum effects on the electrical performance of the MJSCs. The novelty of this paper is the development of a high concentration CPV system that integrates multiple MJSCs with a uniform distribution of rays, unlike the conventional CPV systems that utilise a single concentrator onto a single MJSC. The optical efficiency of the CPV system was also examined using both the types of homogeniser (reflective and refractive).
The escalating demand for solar thermal energy, coupled with the current inefficiencies in existing systems, underscores the critical need for innovative advancements in thermal storage solar collectors. The efficiency of solar collectors relies not solely on design effectiveness but also on the thermophysical properties, such as heat capacity and thermal conductivity, inherent in the working fluid. This study investigates a novel solar collector with a gross area of 0.36 m2, operating on the principle of direct absorption. Experimental investigations were done at various tilt angles (15°, 20°, and 30°) with respect to the horizontal, considering different flow rates and nanofluid settlement within the base fluids. The use of Al2O3 nanoparticles into the base fluid as water, exhibits significant positive effects on the thermophysical properties of the nanofluids, with a volume concentration of 0.003%. The efficiency of the solar collector was calculated across three mass flow rates (0.5, 1, and 1.33 L/min) at each tilt angle. Notably, the study reveals that the efficiency peaks at a 15° tilt due to an optimal flow configuration for maximum energy harvest across all three mass flow rates. Increasing the mass flow rate yields efficiency increments for all tilt angles (15°, 20°, and 30°), with 1 L/min emerging as the optimal mass-flow rate in most cases. This research not only addresses the immediate need for improved solar thermal technologies but also aligns with global sustainability goals, contributing to the IEA Net Zero Emissions initiative and supporting UN Sustainable Development Goals 7, 9, and 11. The paper also includes a critical literature review on the use of nanofluids in solar thermal collectors to improve thermo-physical properties and enhance solar efficiency. Additionally, the key findings regarding the influence and tilt angle on solar efficiency are discussed.