Renewed interest in freeze desalination has emerged due to its advantages over other desalination technologies. A major advantage of the freeze desalination process over evaporative methods is its lower energy consumption (latent heat of freezing is 333.5 kJ/kg and latent heat of evaporation is 2256.7 kJ/kg). Cryogenic fluids like LN2/LAir are emerging as an effective energy storage medium to maximise utilisation of intermittent renewable energy sources. The recovery of this stored cold energy has the potential to be used for freeze desalination. Computational Fluid Dynamics (CFD) modelling was developed to simulate the evaporation of liquid nitrogen to simultaneously conduct freeze desalination to investigate the feasibility of using cryogenic energy for freeze desalination. This integrated CFD model was validated using experimental heat exchanger test facility constructed, to evaporate liquid nitrogen to supply the cooling required for freezing. Parametric study on the LN2 flow rate to observe the volume of ice obtained was also examined using CFD, where increasing the velocity of LN2 by 6 times, increased the volume of ice obtained by 4.3 times. A number of freezing stages were required in order to reduce the ice salinity from 1.5% down to 0.1% as regarded by the World Health Organisation (WHO) as safe to drink. In the cryogenic desalination test rig, approximately 1.35 L of liquid nitrogen was required to reduce the ice salinity from 1.5% to less than 0.1%. Furthermore, the above results illustrate the potential of using the cold energy of cryogenic fluids such as Liquified Natural Gas (LNG) and LN2/LAir for freeze desalination applications as most cold energy during LNG regasification has been unexploited today.
This chapter introduces a comprehensive overview about the principles, challenges and applications of adsorption refrigeration systems (ARSs), as a promising sustainable solution for many of cooling and heating applications. In addition to the features and the basics of ARSs, the following topics have been covered such as characteristics of working pairs, trends in improving the heat and mass transfer of the adsorber; advanced adsorption cycles and performance and operational data of some adsorption refrigeration applications. In some details, the operating range and the performance of ARSs are greatly affected by the employed working adsorbent/refrigerant pairs. Therefore, the study, development and optimum selection of adsorbent/refrigerant pairs, particularly the composite adsorbents, can lead to improving the performance and reliability of ARSs. Regarding the enhancement of heat and mass transfer in the adsorbent bed, two methods are commonly used: one is the development of adsorbents through different coating technologies or new materials such as metal-organic frameworks, and the second is the optimization of the adsorber geometrical parameters and cycle modes. Finally, a brief on some adsorption chillers applications have started to find their share in markets and driven by solar or waste heats.
Small-Scale Turbines (SSTs) are among the most important energy-extraction-enabling technologies in domestic power production systems. However, owing to centrifugal forces, the high rotating speed of SSTs causes excessive strains in the aerofoil portions of the turbine blades. In this paper, a structural performance analysis is provided by combining Finite Element Methods (FEM) with Computational Fluid Dynamics (CFD). The primary objective was to examine the mechanical stresses of a Small-Scale Radial Turbine (SSRT) constructed utilizing 3D printing technology and a novel plastic material, RGD 525, to construct a SSRT model experimentally. After introducing a suitable turbine aerodynamics model, the turbine assembly and related loads were translated to a structural model. Subsequently, a structural analysis was conducted under various loading situations to determine the influence of different rotational speed values and blade shapes on the stress distribution and displacement. Maximum von Mises and maximum main stresses are significantly affected by both the rotor rotational speed and the working fluid input temperature, according to the findings of this research. The maximum permitted deformation, on the other hand, was more influenced by rotational speed, while the maximum allowable fatigue life was more influenced by rotating speed and fluid intake temperature. Also, the region of the tip shroud in the rotor had greater deflection values of 21% of the blade tip width.
This paper investigates the potential of a new integrated solar concentrated photovoltaic (CPV) system that uses a solo point focus Fresnel lens for multiple multi-junction solar cells (MJSCs). The proposed system comprises of an FL concentrator as the primary optical element, a multi-leg homogeniser as the secondary optical element (SOE), a plano-concave lens, and four MJSCs. A three-dimensional model of this system was developed using the ray tracing method to predict the influence of aperture width, height, and position with respect to MJSCs of different reflective and refractive SOE on the overall optical efficiency of the system and the irradiance uniformity achieved on the MJSCs’ surfaces. The results show that the refractive homogeniser using N-BK7 glass can achieve higher optical efficiency (79%) compared to the reflective homogeniser (57.5%). In addition, the peak to average ratio of illumination at MJSCs for the reflective homogeniser ranges from 1.07 to 1.14, while for the refractive homogeniser, it ranges from 1.06 to 1.34, causing minimum effects on the electrical performance of the MJSCs. The novelty of this paper is the development of a high concentration CPV system that integrates multiple MJSCs with a uniform distribution of rays, unlike the conventional CPV systems that utilise a single concentrator onto a single MJSC. The optical efficiency of the CPV system was also examined using both the types of homogeniser (reflective and refractive).
Greenhouses with efficient controlled environment offer a promising solution for food security against the impacts of increasing global temperatures and growing water scarcity. However, current technologies used to achieve this controlled environment consume a significant amount of energy, which impacts on operational costs and CO2 emissions. Using advanced metal organic framework materials (MOFs) with superior water adsorption characteristics, this work investigates the development of a new technology for a greenhouse-controlled environment. The system consists of MOF coated heat exchanger, air to air heat exchanger, and evaporative cooler. A three-dimensional computational fluid dynamics (CFD) model was developed using COMSOL software and experimentally validated for the MOF-801/Graphene coated heat exchanger (DCHE) to determine the best cycle time and power input. It was found that using desorption time of 16 min and power input of 1.26 W, the maximum water removal rate was obtained from MOF-801/Graphene of 274.4 g/kgMOF/W.hr. In addition, an overall mathematical model for the greenhouse climate control was developed and used to investigate the effects of air humidity and velocity on the input air conditions to the greenhouse. Results showed that with high relative humidity levels of 90% in the greenhouse can be conditioned to reach the required relative humidity of 50%.
Heat pipes play vital roles in increasing heat transfer performance of many engineering systems such as solar collectors and this leads to an increase in their usage. Investigation on the performance of heat pipes under different operation conditions and inclination angles is required for effective utilization. In this chapter, a general overview on the construction, operation, advantages, and classifications of heat pipes is presented. Particular attention is given to the heat pipe without wick material in the inner diameter (thermosyphon). Intensive discussions are presented on the construction, operations, advantages and applications of thermosyphon heat pipe. The experimental and numerical approaches on the performance evaluation and characterization of thermosyphon are discussed. A detailed procedure on how experimental work is carried out on thermosyphon is discussed including instrumentation and calibration of the devices. Modelling and simulation of the performance of thermosyphon are discussed, including the model set-up procedure. Factors affecting the performance of thermosyphon such as fill ratio, working fluid, heat input, inclination angles, are analysed based on the overall thermal resistance and thermosyphon performance. Current researches on the effects of major factors affecting the operation of thermosyphon are presented, as well as their current development and various applications in engineering systems.