While the third harmonic of a monochromatic pump field with a frequency ${\omega }_0$ is generated exactly at the frequency $3{\omega }_0$, frequency tripling of broadband ultrashort pump pulses in extended nonlinear media tends to generate isolated spectral peaks substantially shifted from $3{\omega }_0$. We demonstrate this phenomenon by studying nonlinear spectral transformations of femtosecond Cr:forsterite laser pulses in multimode photonic-crystal fibers. Third-harmonic generation is shown to map adjacent guided modes of the third harmonic onto a manifold of spectral peaks within a $150\text{−}\mathrm{THz}$ range around $3{\omega }_0$. The spectral shifts and the widths of these peaks are controlled by the phase and group-velocity mismatch between the pump field and third-harmonic modes, as well as the length of nonlinear-optical interaction and broadening of the pump spectrum, allowing the spectral content of the third-harmonic signal to be engineered by tailoring the fiber dispersion.

In this paper, the analysis of silicon oxynitride (SiON) films, deposited utilizing the plasma enhanced chemical vapor deposition (PECVD) process, for optical waveguides on silicon wafers is presented. The impact of N₂O flow rate on various SiON film properties was investigated. The thickness and refractive index were measured by micro-spot spectroscopic reflectometry and confirmed by spectroscopic ellipsometry. The chemical composition of SiON films was analyzed using Secondary Ion Mass Spectrometry (SIMS). The surface roughness was analyzed using Atomic Force Microscopy (AFM). Increasing the N₂O flow rate during deposition caused the deposition rate to increase and the refractive index to decrease. By changing the flow rate of gases into the chamber during the PECVD process, it is possible to precisely adjust the oxygen (O₂) ratio and nitrogen (N₂) ratio in the SiON film and thus control its optical properties. This was possibility utilized to fabricate SiON films suitable to serve as a waveguide core for optical waveguides with a low refractive index contrast.

Surface plasmon resonance (SPR)-based sensors have attracted huge interest due to their ability to provide real-time sensing of a wide range of quantities, while still boasting high sensitivity, low cost, and electromagnetic immunity. Among various types of these sensors, waveguide-based sensors show great promise in terms of integrability into more complex circuits while still maintaining similar sensitivity and versatility as their stand-alone counterparts. This paper presents the results of investigation based on design and simulation of optimal parameters for multimode SPR-based waveguide sensor sensitive to any commonly used liquid analytes. The sensitivity for a wider range of analytes is achieved by utilisation of SiON material platform because refractive index adjustability of SiON offers a way to tailor sensor’s sensitivity to exact applications and analytes. One of the research goals in this work was to show that multi-mode waveguides may be suitable for such sensors with comparable sensitivity and higher transmission rates as single-mode waveguides. To showcase design possibilities, two variations with the same design and material’s refractive index adjustment only were investigated, and their optimal parameters have been found. Sensitivity for all commonly used liquid analytes was validated, with sensitivity rising to 1400 nm/RIU for label-free refractive index sensing, even without the use of any sensitivity-enhancing structures.

Planar MMI couplers based on inorganic material platforms have played an essential role in photonic integrated circuits development. Advances in organic polymer fabrication techniques enable the design of components beyond a single plane, thus facilitating vertical integration for a wide range of components, including the MMI coupler. This paper presents the design of two 3D IP-dip polymer-based MMI power splitters operating in the near-infrared part of the spectrum at a wavelength of 1550 nm. The resulting output power ratio, modal field distributions, spectral characteristics, and the effects of input fibre misalignment are investigated using the beam propagation method. The fabrication method used to realise the designed splitters was direct laser writing. The function of the splitters was then verified by a highly resolved near-field scanning optical microscope.

Design, simulation, and optimization of the $1\times 4$ optical three-dimensional multimode interference splitter using IP-Dip polymer as a core and polydimethylsiloxane (PDMS) Sylgard 184 as a cladding is demonstrated. The splitter was simulated by using beam propagation method in BeamPROP simulation module of RSoft photonic tool and optimized for an operating wavelength of 1.55 $\mu\mathrm{m}$ . According to the minimum insertion loss, the dimensions of the splitter were optimized for a waveguide with a core size of $4\times 4\ \mu \mathrm{m}^{2}$ . The objective of the study is to create the design for fabrication by three-dimensional direct laser writing optical lithography.