The aim of this work is to investigate the degradation of perovskite solar cells (PSCs) by means of impedance spectroscopy, a highly sensitive characterization technique used to establish the electrical response of a device in a nondestructive manner. In this paper, PSCs with two different electron transport layers (ETLs) are studied: PSCs with undoped SnO2 as an ETL are compared to PSCs with an ETL composed of graphene-doped SnO2 (G-SnO2). Experimental data were collected immediately after fabrication and after one week, monitoring both impedance spectroscopy and dark current-voltage (I-V) curves. It was observed that, in the case of the undoped PSCs, the degradation of the solar cells affected both the AC behavior of the devices, modifying the associated Nyquist plots, and the DC behavior, observable from the dark I-V measurements. Conversely, the solar cells with G-SnO2 showed no variation. Considering the Nyquist plots, a quantitative analysis was performed by comparing the parameters of a proper equivalent circuit model. The results were coherent with those achieved in the DC analysis, thus proving that the analysis of impedance spectra, supported with dark I-V curves, allows one to gain a deeper knowledge of the degradation phenomena of perovskite solar cells. This study opens the door for further improvement of these devices through a better understanding of their electrical behavior.
Perovskite/silicon tandem solar cells have strong potential for high efficiency and low cost photovoltaics. In monolithic (two-terminal) configurations, one key element is the interconnection region of the two subcells, which should be designed for optimal light management and prevention of parasitic p/n junctions. We investigated monolithic perovskite/silicon-heterojunction (SHJ) tandem solar cells with a p/n nanocrystalline silicon/silicon-oxide recombination junction for improved infrared light management. This design can additionally provide for resilience to shunts and simplified cell processing. We probed modified SHJ solar cells, made from double-side polished n-type Si wafers, which included the proposed front-side p/n tunnel junction with the p-type film simultaneously functioning as selective charge transport layer for the SHJ bottom cell, trying different thicknesses for the n-type layer. Full tandem devices were then tested, by applying a planar n-i-p mixed-cation mixed-halide perovskite top cell, fabricated via low temperature solution methods to be compatible with the processed Si wafer. We demonstrate the feasibility of this tandem cell configuration over a 1 cm2 area with negligible J-V hysteresis and a VOC ~1.8 V, matching the sum of the VOC-s contributed by the two components.
Inorganic perovskite CsPbI3 solar cells hold great potential for improving the operational stability of perovskite photovoltaics. However, electron extraction is limited by the low conductivity of TiO2, representing a bottleneck for achieving stable performance. In this study, a co‐doping strategy for TiO2 using Nb(V) and Sn(IV), which reduces the material's work function by 80 meV compared to Nb(V) mono‐doped TiO2, is introduced. To gain fundamental understanding of the processes at the interfaces between the perovskite and charge‐selective layer, transient surface photovoltage measurements are applied, revealing the beneficial effect of the energetic and structural modification on electron extraction across the CsPbI3/TiO2 interface. Using 2D drift‐diffusion simulations, it is found that co‐doping reduces the interface hole recombination velocity by two orders of magnitude, increasing the concentration of extracted electrons by 20%. When integrated into n–i–p solar cells, co‐doped TiO2 enhances the projected TS80 lifetimes under continuous AM1.5G illumination by a factor of 25 compared to mono‐doped TiO2. This study provides fundamental insights into interfacial charge extraction and its correlation with operational stability of perovskite solar cells, offering potential applications for other charge‐selective contacts.
Characterizing the electron transport layer (ETL)/perovskite interface in perovskite solar cells (PSCs) is of paramount importance for their overall performance. In this article the effect of different concentrations of graphene nanoplatelets in addition to SnO 2 is investigated by considering degradation over time. PSCs behavior is monitored by collecting dark current–voltage curves as fabricated and after two months. A deeper insight is gained through impedance spectroscopy analysis. From Nyquist plots equivalent circuit models and the corresponding time constants are extracted. Moreover, resistive part of the impedance associated with high frequency has been related to static shunt resistance, assessing one of the considered ETL doping concentration as the more suitable choice to reduce degradation.
Improving morphological and electronic properties of the electron transport layer (ETL) is a critical issue to fabricate highly efficient perovskite solar cells. Tin dioxide is used as an ETL for its peculiarities such as low-temperature solution-process and high electron mobility and several handlings have been tested to increase its performances. Herein, SnO2:ZnO and SnO2:In2O3 composites are studied as ETL in planar n-i-p CH3NH3PbI3 solar cells fabricated in ambient air, starting from glass/ITO substrates. Morphological, electrical and optical properties of zinc- and indium-oxide nanoparticles (NPs) are investigated. First-principle calculations are also reported and help to further explain the experimental evidences. Photovoltaic performances of full devices show an improvement in efficiency for SnO2:In2O3–based solar cells with respect to pristine SnO2, probably due to a suppression of interfacial charge recombination between ITO/ETL and ETL/perovskite. Moreover, a better homogeneity of SnO2:In2O3 deposition with respect to SnO2:ZnO composites, conducts an increase in perovskite grain size and, consequently, the device performances.
In recent years, SnO2 quantum dots (QDs) have been widely used for preparing the electron‐transport layer within perovskite solar cells (PSCs). However, the fabricated devices exhibit an evident hysteresis unless interlayer materials are introduced to passivate or prevent the formation of trap states at the SnO2–perovskite interface. Herein, the use of the zwitterion 3‐(1‐pyridinio)‐1‐propanesulfonate (PPS) as additive inside the SnO2 QDs solution is proposed. The results highlight that the PPS plays a multifunctional role by accelerating the synthesis of the QDs, enhancing the electron transfer and passivating defects at the SnO2–perovskite interface. The resulting PSCs with SnO2 QDs incorporating PPS exhibit a remarkable reduction in hysteresis index (HI) compared to those prepared with thiourea or without any additives. This reduction in HI suggests that PPS serves as a cost‐effective alternative additive for SnO2 QDs preparation, eliminating the need for additional interlayers or expensive additives.