Ahmed ALtaher Omer

Mr. Ahmed ALtaher Omer

Faculty of Wood engineering, University of Sopron, Sopron, Hungary
orcid

Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
14 November 2023 in Materials
Verified
Journal Article
Open access
PDF file
Ahmed ALtaher OmerAhmed ALtaher Omer
Ahmed ALtaher Omer
JGJózsef Garab
József Garab
EHErika Horváth-Szováti
Erika Horváth-Szováti
JKJános Kozelka
János Kozelka
Bejó LászlóBejó László
Bejó László
Cross-laminated timber (CLT) has become a massive commercial success in recent years due to its high performance, technological advantages, and low environmental impact. The finite softwood raw material supply has motivated researchers to find alternatives. This study presents an investigation of the viability of some Hungarian hardwood materials, such as CLT materials. Homogeneous beech, poplar, and spruce panels, as well as their combinations, were created using a polyurethane adhesive. The experimental results show the clear potential of Hungarian poplar, which performed much better than spruce. Poplar’s modulus of elasticity (MOE) and modulus of rupture (MOR) values reached or exceeded those of high-grade commercial softwood CLT. The bending properties of beech and hybrid beech–poplar panels far exceeded the performance of commercial panels, which shows the excellent potential of high-density hardwoods for high-performance CLT production. Beech–spruce hybrid panels seriously underperformed. This was caused by gluing issues, probably due to the large density differences between the two species, as evidenced by the glueline failure exhibited by most of these specimens during testing. The average panel density proved to be the best predictor of mechanical performance, except for beech–spruce hybrid panels.

30 September 2025 in Forests
Verified
Journal Article
Open access
PDF file
Ahmed ALtaher OmerAhmed ALtaher Omer
Ahmed ALtaher Omer
CCCsilla CSIHA
Csilla CSIHA
Tibor AlpárTibor Alpár
Tibor Alpár
Bejó LászlóBejó László
Bejó László
The increasing demand for sustainable raw materials in engineered wood production has prompted the evaluation of alternative raw materials. In this context, indigenous black poplar (Populus nigra) was analyzed as a potential alternative, by testing its wettability, characterized by contact angle, determined by the sessile drop method, to predict its adhesion when used as strands for OSB and LSL production. Surface tension was tested on strands with a wide range of surface roughnesses. The results show minor but statistically significant difference in favor of black poplar, which has somewhat lower contact angle values (62.01°) than hybrid poplar (64.71°), based on 300 measurements each. The absorption of the liquid into the strands, evaluated on a smaller sample, follows a logarithmic relation with time. These results also show a slightly faster decrease in contact angle in case of indigenous poplar, compared to hybrid poplar. The results indicate that the adhesion of indigenous poplar strands does not present extra challenges, compared to the currently more frequent hybrid poplar strands.

13 May 2026 in Forests
Verified
Journal Article
Open access
PDF file
JGJózsef Garab
József Garab
ZTZsolt Toth
Zsolt Toth
Ahmed ALtaher OmerAhmed ALtaher Omer
Ahmed ALtaher Omer
Bejó LászlóBejó László
Bejó László
Screw withdrawal force is a key mechanical property related to the load-bearing capacity and reliability of mechanically fastened timber structures. This study investigates the screw withdrawal performance of cross-laminated timber (CLT) manufactured from spruce, beech, and poplar, including both homogeneous and hybrid layups. The selected species represent materials with different densities and regional availability in Hungary. A one-component polyurethane adhesive was used for panel manufacturing. Screw withdrawal force was determined using two methods: a universal testing machine (UTM) and a manual portable device (MPD). The highest withdrawal forces were observed in beech-based configurations, while the lowest values were measured for spruce. Poplar-based configurations demonstrated intermediate but competitive performance, exceeding the reference spruce values. Statistical evaluation confirmed a significant effect of layup configuration on withdrawal resistance. The MPD measurements were on average approximately 9% higher than UTM results, indicating a consistent and quantifiable inter-method difference. The results demonstrate that hybrid CLT configurations can be optimized by combining species of different densities and that portable testing methods provide reliable estimates of withdrawal performance. These findings contribute to the understanding of connection behavior in hybrid CLT and support the practical application of semi-destructive testing methods for in-situ assessment.

14 July 2026 in Forests
Verified
Journal Article
Open access
PDF file
Ahmed ALtaher OmerAhmed ALtaher Omer
Ahmed ALtaher Omer
Tibor AlpárTibor Alpár
Tibor Alpár
Bejó LászlóBejó László
Bejó László
Geometric uniformity in lignocellulosic furnish plays a central role in determining the mechanical reliability and density stratification of engineered wood products. This study presents a comprehensive morphological assessment of wood strands produced from indigenous poplar (Populus nigra L.) and hybrid poplar (Populus × euramericana (Dode) Guinier) strands under full industrial flaking conditions. A total of 600 strands were characterized for weight, length, width, and thickness and analyzed using a multivariate statistical framework integrating Principal Component Analysis (PCA) and bivariate correlation modeling. Despite being processed to the same nominal target length (120 mm), the two provenances exhibited markedly different dimensional behaviors. Hybrid poplar strands were substantially heavier (mean 0.536 g vs. 0.291 g) and slightly thicker on average, while indigenous strands were marginally wider; strand length did not differ significantly between provenances (p = 0.354). PCA applied to four variables (weight, length, width, and mean thickness) revealed that weight and width were the dominant contributors to PC1 (57.0% of total variance), enabling clear separation of the two provenances into distinct multivariate clusters. These findings indicate that hybrid furnish, due to its coarser and more variable geometry, may require enhanced mat densification during hot pressing to minimize internal voids and achieve a stable vertical density profile (VDP). The dataset and analytical approach presented here provide actionable insights for optimizing flaker calibration, strand classification, and resin dosing strategies in the production of Oriented Strand Board (OSB) and Laminated Strand Lumber (LSL), particularly when integrating fast-growing hybrid poplar resources into industrial manufacturing lines.