This paper presents results of research on the preparation of biochar-modified rigid polyurethane foams that could be successfully used as thermal insulation materials. The biochar was introduced into polyurethane systems in an amount of up to 20 wt.%. As a result, foam cells became elongated in the direction of foam growth and their cross-sectional areas decreased. The filler-containing systems exhibited a reduction in their apparent densities of up to 20% compared to the unfilled system while maintaining a thermal conductivity of 25 mW/m·K. Biochar in rigid polyurethane foams improved their dimensional and thermal stability.

This paper presents research into the preparation of rigid polyurethane foams with bio-polyols from rapeseed and tall oil. Rigid polyurethane foams were designed with a cryogenic insulation application for aerospace in mind. The polyurethane systems containing non-renewable diethylene glycol (DEG) were modified by replacing it with rapeseed oil-based low functional polyol (LF), obtained by a two-step reaction of epoxidation and oxirane ring opening with 1-hexanol. It was observed that as the proportion of the LF polyol in the polyurethane system increased, so too did the apparent density of the foam material. An increase in the value of the thermal conductivity coefficient was associated with an increase in the value of apparent density. Mechanical tests showed that the rigid polyurethane foam had higher compressive strength at cryogenic temperatures compared with the values obtained at room temperature. The adhesion test indicated that the foams subjected to cryo-shock obtained similar values of adhesion strength to the materials that were not subjected to this test. The results obtained were higher than 0.1 MPa, which is a favourable value for foam materials in low-temperature applications.

Rigid polyurethane foams were obtained using two types of renewable raw materials: bio-polyols and a cellulose filler (ARBOCEL^® P 4000 X, JRS Rettenmaier, Rosenberg, Germany). A polyurethane system containing 40 wt.% of rapeseed oil-based polyols was modified with the cellulose filler in amounts of 1, 2, and 3 php (per hundred polyols). The cellulose was incorporated into the polyol premix as filler dispersion in a petrochemical polyol made using calenders. The cellulose filler was examined in terms of the degree of crystallinity using the powder X-ray diffraction PXRD -and the presence of bonds by means of the fourier transform infrared spectroscopy FT-IR. It was found that the addition of the cellulose filler increased the number of cells in the foams in both cross-sections—parallel and perpendicular to the direction of the foam growth—while reducing the sizes of those cells. Additionally, the foams had closed cell contents of more than 90% and initial thermal conductivity coefficients of 24.8 mW/m∙K. The insulation materials were dimensionally stable, especially at temperatures close to 0 °C, which qualifies them for use as insulation at low temperatures.

We report on rigid polyurethane (PUR) foams prepared using different contents of a mixture of two bio-polyols (20–40 php). The bio-polyols were obtained through epoxidation and a ring opening reaction. Different chemical structures of the bio-polyols resulted from the use of 1-hexanol and 1,6-hexanediol as opening agents. The bio-polyols were characterized by hydroxyl values of 104 and 250 mgKOH/g and viscosities of 643 and 5128 mPa·s, respectively. Next, the influence of the bio-polyols on the foaming process of PUR systems as well as the foam properties was evaluated. The bio-foams modified with different contents of the bio-polyols were next compared with a reference foam obtained using a polyether petrochemical polyol. The effect of the apparent density reduction as a result of replacing the petrochemical polyol was minimized by decreasing the water content in the formulation. It was found that the modification of the recipe by changing the content of water, acting as a chemical foaming agent, did not affect the foaming process. However, the introduction of the bio-polyols mixture limited the reactivity of the systems by reducing the maximum temperature of the foaming process. The bio-materials with comparable apparent densities to that of the reference material were characterized by similar values of the thermal conductivity coefficient and a decrease in their mechanical strengths. A deterioration of mechanical properties was caused by the plasticization of the polyurethane matrices with the bio-polyols containing dangling chains. However, all materials were dimensionally stable at room temperature.

This article presents the results of research on obtaining new polyurethane (PUR) foams modified with thermally expanded vermiculite. The filler was added in amount of 3 wt.% up to 15 wt.%. The additionally applied procedure of immersion the non-organic filler in H₂O₂ was performed to increase the exfoliation effect of thermally treated mineral and additional oxidation the surfaces. The effect of fillers on foaming process, cell structure, thermal insulation, apparent density, compressive strength, thermal properties, and flammability are assessed. The foaming process of PUR foams modified with vermiculite was comparable for all systems, regardless of the content of the filler. A slight increase in reactivity was observed, confirmed by a faster decrease in dielectric polarization for the system with modified vermiculite by H₂O₂. The modification of the reference system with the vermiculite increased the content of closed cells from 76% to 91% for the foams with the highest vermiculite content. Coefficient of thermal conductivity of reference foam and foams modified with vermiculite was in the range 24–26 mW/mK. The use of vermiculite up to 15 wt.% did not influence significantly on mechanical properties and flammability, which from an economic point of view is important because it is possible to reduce the cost of materials by introducing a cheap filler without deteriorating their properties.

This article compares the properties of closed-cell PUR bio-foams produced on a laboratory scale and on an industrial scale. In the formulation used, the polyol premix contained 40 wt.% of a bio-polyol based on rapeseed oil. Selected useful properties of the foams obtained on the two scales and the use of one-step and spraying methods were compared. In the case of the spraying method, the experimental system was compared to a commercial one. Given the possibility of applying the bio-foams in insulation systems for cryogenic and liquefied natural gas (LNG) applications, a compressive strength analysis of the foams was carried out at room temperature as well as at −196 °C. It was found that the foams modified with the bio-polyol were characterized by a higher compressive strength at low temperatures than commercial foams based on a petrochemical polyol.