Seung S. Lee

Dr. Seung S. Lee


Research Focus & Metrics

Academic Career Length

25Years (2002-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
21 May 2012 in Advanced Materials
Verified
Journal Article
Closed access
PDF file
PLPhillip Lee
Phillip Lee
JLJinhwan Lee
Jinhwan Lee
HLHyungman Lee
Hyungman Lee
JYJunyeob Yeo
Junyeob Yeo
SHSukjoon Hong
Sukjoon Hong
Seung Hwan KOSeung Hwan KO
Seung Hwan KO

16 October 2018 in Nature Communications
Verified
Journal Article
Open access
PDF file
MLMikyung Lim
Mikyung Lim
JSJaeman Song
Jaeman Song
SLSeung S. Lee
Seung S. Lee
BLBong Jae Lee
Bong Jae Lee
Several experiments have shown a huge enhancement in thermal radiation over the blackbody limit when two objects are separated by nanoscale gaps. Although those measurements only demonstrated enhanced radiation between homogeneous materials, theoretical studies now focus on controlling the near-field radiation by tuning surface polaritons supported in nanomaterials. Here, we experimentally demonstrate near-field thermal radiation between metallo-dielectric multilayers at nanoscale gaps. Significant enhancement in heat transfer is achieved due to the coupling of surface plasmon polaritons (SPPs) supported at multiple metal-dielectric interfaces. This enables the metallo-dielectric multilayers at a 160-nm vacuum gap to have the same heat transfer rate as that between semi-infinite metal surfaces separated by only 75 nm. We also demonstrate that near-field thermal radiation can be readily tuned by modifying the resonance condition of coupled SPPs. This study will provide a new direction for exploiting surface-polariton-mediated near-field thermal radiation between planar structures.

23 July 2020 in Physical Review Applied
Verified
Journal Article
Closed access
PDF file
MLMikyung Lim
Mikyung Lim
JSJaeman Song
Jaeman Song
SLSeung S. Lee
Seung S. Lee
Jungchul LeeJungchul Lee
Jungchul Lee
BLBong Jae Lee
Bong Jae Lee
Here, we demonstrate a substantially increased near-field radiative heat transfer between asymmetric structures (i.e., doped Si and SiO2) by using a thin Ti film as a plasmonic coupler. The measured near-field enhancement at vacuum gap of 380 nm is found to be 3.5 times greater than that for the case without the coupler. The enhancement mechanism is thoroughly elucidated for both polarizations, and a dimensionless parameter, which can quantify the coupling strength of the surface polaritons across the vacuum interfaces, is proposed.

7 April 2014 in Optics Express
Verified
Journal Article
Closed access
PDF file
HLHyungman Lee
Hyungman Lee
DLDongjin Lee
Dongjin Lee
JHJunghwan Hwang
Junghwan Hwang
DNDongil Nam
Dongil Nam
CBChangwan Byeon
Changwan Byeon
SLSeung S. Lee
Seung S. Lee
In this study, we propose new fusion technology to overcome the limitations of the current printing process for printed electronics. The combinative slot-die coating and laser direct writing on a roll-to-roll (R2R) basis was studied and applied to the fabrication of piezoresistive strain gauges. Piezoresistive sensors were fabricated for the first time by this developed fusion technology. A parametric study was performed for the R2R process, followed by a comparison of the fabricated functional devices with commercial products, which confirmed a 40% increase in the gauge factor of the fabricated sensors over the commercial product. The combinative manufacturing process for functional device fabrication will open a new chapter in the future of printed electronics due to its large area capacity at low cost.

1 June 2014 in ETRI Journal
Verified
Journal Article
Open access
PDF file
CLChang Hwa Lee
Chang Hwa Lee
SLSeung S. Lee
Seung S. Lee
In this paper, a new, simple capacitive tilt sensor with a metallic ball is proposed. The proposed tilt sensor has only two electrodes and a metallic ball, and this design assists in managing the inherent contact problem in measuring tilt angles. Capacitive sensing, compared with other types of tilt sensor, has many advantages such as simplicity, noncontact measurement, long-throw linear displacement, and sub-micron plate spacing. Its design and fabrication process are significantly simpler than previous types of tilt sensors. The dimensions of the prototype tilt sensor are 20?mm???20?mm , and the diameter of the polystyrene tube is 5 mm with a tube thickness of 0.15 mm. An analytical study of the prototype capacitive tilt sensor was undertaken, and the experimental results demonstrate the relationship between the tilt angles and measured capacitances compared with the analytical study.

22 June 2012 in Advanced Materials
Verified
Journal Article
Closed access
PDF file
PLPhillip Lee
Phillip Lee
JLJinhwan Lee
Jinhwan Lee
HLHyungman Lee
Hyungman Lee
JYJunyeob Yeo
Junyeob Yeo
SHSukjoon Hong
Sukjoon Hong
Seung Hwan KOSeung Hwan KO
Seung Hwan KO