Luis Humberto Díaz Saldierna

Dr. Luis Humberto Díaz Saldierna

orcid

Research Focus & Metrics

Academic Career Length

20Years (2007-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 September 2009 in IET Power Electronics
Verified
Journal Article
Closed access
JLJ. Leyva-Ramos
J. Leyva-Ramos
MOM.G. Ortiz-Lopez
M.G. Ortiz-Lopez
LSLuis Humberto Díaz Saldierna
Luis Humberto Díaz Saldierna
JMJ.A. Morales-Saldaña
J.A. Morales-Saldaña
A controller design methodology for a quadratic boost converter with a single active switch is developed. This converter has two LC filters; thus, it will exhibit fourth-order characteristic dynamics. However, only the first inductor current and the output capacitor voltage are selected for feedback purposes. This current can also be used for one-cycle overload protection; therefore, the full benefits of current-mode control are maintained. Average current-mode control is selected over peak current-mode control because this strategy provides a faster transient response and better noise immunity. The high-gain compensator of the current loop helps tracking the current programme with a high degree of accuracy. The robustness of the proposed controller is tested under changes in the input voltage, output load and reference signal.

23 January 2018 in IEEE Journal of Emerging and Selected Topics in Power Electronics
Verified
Journal Article
Closed access
YZYuz A. Zuniga-Ventura
Yuz A. Zuniga-Ventura
DLDiego Langarica-Cordoba
Diego Langarica-Cordoba
JLJesus Leyva-Ramos
Jesus Leyva-Ramos
LSLuis Humberto Díaz Saldierna
Luis Humberto Díaz Saldierna
Victor Manuel Ramirez RiveraVictor Manuel Ramirez Rivera
Victor Manuel Ramirez Rivera
This work proposes an output voltage regulation scheme for a fuel-cell based power source. The proposed methodology relies on the design of a dynamic backstepping average current mode controller considering the combined fuel-cell stack and boost converter model. Also, an external loop for voltage regulation using a proportional-integral (PI) action is added. Moreover, to improve the robustness of the current loop, a load estimator using immersion-invariance (I&I) approach is designed. As a result, an adaptive backstepping controller ensuring asymptotic stability via a Lyapunov function is achieved. Finally, based on a 460 W testbench and a DSPACE platform, the closed-loop system performance is evaluated through experimental results. An appropriate output voltage regulation and robust behavior concerning to load variation and fuel-cell stack unregulated DC output voltage are exhibited.

4 January 2011 in IET Power Electronics
Verified
Journal Article
Closed access
JLJ. Leyva-Ramos
J. Leyva-Ramos
MOM.G. Ortiz-Lopez
M.G. Ortiz-Lopez
LSLuis Humberto Díaz Saldierna
Luis Humberto Díaz Saldierna
MMM. Martinez-Cruz
M. Martinez-Cruz
A controller design methodology for an n-stage cascade boost converter is given using average current-mode control. This class of converters has n-LC filters; thus, it will exhibit 2n-order characteristic dynamics. The proposed scheme employs the inductor current of the input stage and the capacitor voltage of the output stage; thus, there are (n−1) capacitor voltages and (n−1) inductor currents that are not used for feedback purposes. The sensed current can also be used for one-cycle overload protection; therefore the full benefits of current-mode control are maintained. Owing to the fact that this scheme uses only a reduced set of variables for feedback, it is important to study the internal stability. The results given in this study allow the designer to easily pinpoint the control circuit parameters that optimise the converter's performance. Experimental results are given for a 100 W switching regulator where the robustness of the proposed controller is tested under changes in the input voltage and output load.

1 September 2013 in IET Power Electronics
Verified
Journal Article
Open access
PDF file
JLJesus Leyva-Ramos
Jesus Leyva-Ramos
JLJuan Manuel Lopez‐Cruz
Juan Manuel Lopez‐Cruz
MOMaria Guadalupe Ortiz‐Lopez
Maria Guadalupe Ortiz‐Lopez
LSLuis Humberto Díaz Saldierna
Luis Humberto Díaz Saldierna
A typical fuel‐cell stack produces a low DC voltage with wide variations; therefore a DC–DC switching converter is required to step up and regulate the output voltage. In this work, a model based on electrical variables is developed for a fuel‐cell stack. This model is later combined with the model of a high step‐up voltage converter to obtain a combined model that incorporates the behaviour of fuel‐cell stack. The resulting model is then used to design an average‐current mode controller for a switching regulator. To test the proposed regulator, a power module with polymer electrolyte membrane fuel cells is used as an input source. This module delivers an output voltage between 26 and 42 V depending on the current being drawn. Experimental results exhibit the robustness of the switching regulator to step changes in the output load and the output voltage of the fuel‐cell stack.

11 January 2023 in Micromachines
Verified
Journal Article
Open access
PDF file
CBCarlo A. Beltrán
Carlo A. Beltrán
LSLuis Humberto Díaz Saldierna
Luis Humberto Díaz Saldierna
DLDiego Langarica-Cordoba
Diego Langarica-Cordoba
PANFILO RAYMUNDO MARTINEZ RODRIGUEZPANFILO RAYMUNDO MARTINEZ RODRIGUEZ
PANFILO RAYMUNDO MARTINEZ RODRIGUEZ
In this paper, a passivity-based control (PBC) scheme for output voltage regulation in a fuel-cell/boost converter system is designed and validated through real-time numerical results. The proposed control scheme is designed as a current-mode control (CMC) scheme with an outer loop (voltage) for voltage regulation and an inner loop (current) for current reference tracking. The inner loop’s design considers the Euler–Lagrange (E-L) formulation to implement a standard PBC and the outer loop is implemented through a standard PI controller. Furthermore, an adaptive law based on immersion and invariance (I&I) theory is designed to enhance the closed-loop system behavior through asymptotic approximation of uncertain parameters such as load and inductor parasitic resistance. The closed-loop system is tested under two scenarios using real-time simulations, where precision and robustness are shown with respect to variations in the fuel cell voltage, load, and output voltage reference.

1 January 2007
Verified
Conference Paper
Closed access
MOM. G. Ortiz-Lopez
M. G. Ortiz-Lopez
JLJ. Leyva-Ramos
J. Leyva-Ramos
LSLuis Humberto Díaz Saldierna
Luis Humberto Díaz Saldierna
JGJ. M. Garcia-Ibarra
J. M. Garcia-Ibarra
ECE. E. Carbajal-Gutierrez
E. E. Carbajal-Gutierrez
In this paper, a methodology for controller design of a quadratic boost converter is given using average current- mode control. It is shown that the transfer function of the first inductor current-to-duty ratio is minimum phase; thus, this inductor current is selected for feedback purposes. For the inner loop, a current gain and a high gain compensator are selected where the corresponding sintonization procedure is given. For the outer loop, a conventional Pi-controller is designed. The design-oriented analytic results allow the designer to easily pinpoint the control circuit parameters that optimize the converter's performance. At the end, experimental results are given for a 49 W switching regulator where step changes between 10% to full load are shown.