PI/SiO2 composite films have been prepared by using in situ polymerization. The influences of the dosage of silane coupling agent (KH-560) on the structure and performance of PI/SiO2 composite film have been investigated. The results show that in the components without KH-560, the addition of SiO2 decreases the transmittance of the sample. Compared to the same SiO2 doping amount, the transmittance in the visible light range of the sample using KH-560 is higher than that of the sample without KH-560. After adding KH-560, the tensile strength, the elastic modulus the elongation at break of the sample have largely changed. The thermal stability and the ability to resist ultraviolet radiation of the composite film first increases and then decreases. Furthermore, the optimal dosage of KH-560 is 3%. Moreover, the addition of KH-560 has little effect on the transmittance of the PI/SiO2 composite films before and after UV irradiation.
Graphene film has wide applications in optoelectronic and photovoltaic devices. A novel and facile method was reported for the reduction of graphene oxide (GO) film by electron transfer and nascent hydrogen produced between aluminum (Al) film deposited by magnetron sputtering and hydrochloric acid (HCl) solution for only 5 min, significantly shorter than by other chemical reduction methods. The thickness of Al film was controlled utilizing a metal detection sensor. The effect of the thickness of Al film and the concentration of HCl solution during the reduction was explored. The optimal thickness of Al film was obtained by UV-Vis spectroscopy and electrical conductivity measurement of reduced GO film. Atomic force microscope images could show the continuous film clearly, which resulted from the overlap of GO flakes, the film had a relatively flat surface morphology, and the surface roughness reduced from 7.68 to 3.13 nm after the Al reduction. The film sheet resistance can be obviously reduced, and it reached 9.38 kΩ/sq with a high transmittance of 80% (at 550 nm). The mechanism of the GO film reduction by electron transfer and nascent hydrogen during the procedure was also proposed and analyzed.
Transparent conductive films are widely used in electronic products and industrial fields. Ultra-thin Ag conductive nanofilm (ACF) was prepared on a soda lime silica glass (ordinary architectural glass) substrate with industrial magnetron sputtering equipment with AZO (Al2O3 doped ZnO) as the crystal bed and wetting layer. In order to improve the corrosion resistance and conductivity of the ACF, graphene nanosheets were modified on the surface of the ACF by electrospraying for the first time. The results show that this graphene modification could be carried out continuously on a meter scale. With the modification of the graphene layer, the corrosion rate of graphene-decorated ACF (G/ACF) can be reduced by 74.56%, and after 72 h of salt spray test, the conductivity of ACF samples without modification of graphene can be reduced by 34.1%, while the conductivity of G/ACF samples with modification of graphene can be reduced by only 6.5%. This work proves the potential of graphene modified ACF to prepare robust large-area transparent conductive film.
Two-dimensional molybdenum disulfide (MoS2) has emerged as a promising candidate for next-generation electronics and optoelectronics; however, its scalable synthesis with precise control over domain size and film continuity remains challenging. Herein, we report a physical vapor deposition (PVD)-assisted chemical vapor deposition (CVD) strategy for the controllable growth of high-quality monolayer MoS2. By thermally evaporating an ultrathin (3 nm) MoO3 precursor film, spontaneous post-deposition dewetting yields a porous honeycomb morphology that significantly enhances vapor–solid reaction kinetics during subsequent sulfurization. Crucially, by modulating the argon carrier gas flow rate to regulate the local sulfur chemical potential, we achieve distinct growth regimes: a high flow rate (70 sccm) suppresses nucleation density, enabling isolated triangular and hexagonal single crystals with lateral dimensions up to 500 μm, whereas a reduced flow rate (50 sccm) promotes high-density nucleation and coalescence into continuous centimeter-scale polycrystalline films. Comprehensive structural and optical characterizations, including atomic force microscopy, Raman spectroscopy, photoluminescence, and X-ray photoelectron spectroscopy, confirm that the synthesized MoS2 exhibits prototypical monolayer thickness (~0.7 nm), well-defined local crystallinity and a direct bandgap emission at 1.84 eV. This work establishes a robust, scalable, and highly tunable route for synthesizing large-area 2D TMDs tailored for advanced device integration.
To combat the critical hurdles of thermal buildup and low-temperature shutdown events in 5G-enabled smart wearables, a high-performance flexible composite film based on ellagic acid-modified single-walled carbon nanotubes (EA-SWCNTs) and aramid nanofibers (ANF) was designed and developed. The influence mechanism of the loading amount of the conductive network on the electrothermal properties of the composite material was focused on. The results show that through the π-π stacking non-covalent modification strategy, the uniform dispersion of EA-SWCNTs on the layer of ANF substrate and the construction of an ordered layered structure were successfully achieved. The prepared composite film could reach a steady-state temperature of 171 °C under a driving voltage of 3.5 V. In addition, it exhibits excellent electrothermal response characteristics and cyclic stability. It could reach the steady-state voltage within 10 s and shows no obvious performance degradation after multiple cycles. This composite film shows broad application prospects in fields such as intelligent wearable devices and flexible electronic protection.
About Me
No 399, Binshui West Rd., Xiqing District,Tianjin ,China
No 399, Binshui West Rd., Xiqing District,Tianjin ,China