Aluminum MMCs are preferred to other conventional materials in the fields of aerospace, automotive and marine applications owing to their improved properties like high strength to weight ratio, good wear resistance etc. In the present work an attempt has been made to synthesize metal matrix composite using 6061Al as matrix material reinforced with ceramic Al2O3 particulates using liquid metallurgy route in particular stir casting technique. The addition level of reinforcement is being varied from 6-12wt% in steps of 3wt%. For each composite, reinforcement particles were preheated to a temperature of 200°C and then dispersed in steps of three into the vortex of molten Al6061 alloy to improve wettability and distribution. Microstructural characterization was carried out for the above prepared composites by taking specimens from central portion of the casting to ensure homogeneous distribution of particles. Hardness and tensile properties of the prepared composite were determined before and after addition of Al2O3 particulates to note the extent of improvement. Microstructural characterization of the composites has revealed fairly uniform distribution and some amount of grain refinement in the specimens. Further, the hardness and tensile properties are higher in case of composites when compared to unreinforced 6061Al matrix, also increasing addition level of reinforcement has resulted in further increase in both hardness and tensile strength
MMC based on aluminium (Al) were produced for light-weight applications especially in aviation and automobile areas. Present paper deals with the fabrication and mechanical performance of AA6061 matrix composites fortified with Al2O3 (alumina) and graphene particulates. Fluid metallurgy method namely stir casting route was employed for fabricating the hybrid composites. Al2O3p and graphene powder are mixed in different weight fractions in which graphene (1 wt. %) particle reinforcement is held consistent and Al2O3 reinforcement is differed freely with 5, 10 and 15 wt. %. Using optical analyser and SEM equipment, microstructural examination is carried out and the result reveals that the graphene and Al2O3 particles prevalently are homogeneously appropriated on the grain limits of Al matrix and Al2O3 particles are disseminated between graphene in the as-cast AA6061 MMC’s. Detailed analysis on investigation of the microstructure and mechanical aspects of Al6061-graphene-Al2O3p composites is presented by following ASTM guidelines; results uncovered that with increment in reinforcement particles, there is an enhancement in the hardness, ultimate strength, yield strength and a decline in the elongation values was however noticed when contrasted with Al6061 alloy. Fractography investigation revealed dimples in unreinforced alloy and the composite.
20 October 2023 in Journal of The Institution of Engineers (India): Series D
An Al2014-alumina (Al2O3) composite's characteristics are significantly influenced by the reinforcement particle size variation. Therefore, this study examines the microstructure, mechanical, fractography, and wear performance of an Al2014-Al2O3p composite made using a unique two-stage stir casting method and various alumina weight fractions (9, 12, and 15 wt %). Three categories of alumina particle size are used, i.e., fine particle size (FPS, 8 μm), intermediate particle size (IPS, 53 μm), and coarse particle size (CPS, 88 μm). The shapes of the composites were characterized using scanning electron microscopy. According to scanning electron microscopic analyses of the microstructure, the FPS dispersion was more uniform than IPS and CPS, whereas CPS causes agglomeration. Additionally, the studies show that the FPS composite outperformed CPS and IPS composites in terms of mechanical characteristics and wear performance. The fractography study shows conical and equiaxed dimple failure in the Al2014 matrix and the circular cavities.
The paper focused on an experimental study on the microstructural, mechanical, and wear characteristics of 15 wt.% alumina (Al2O3) particulates with an average particle size of 20 µm, reinforced in Al2014 alloy matrix composite as-cast and heat-treated samples. The metal matrix composite (MMC)samples were produced via a novel two-stage stir-casting technique. The fabricated composite samples were subjected to evaluate hardness, tensile strength, fatigue behavior and wear properties for both as cast and T6 heat-treated test samples. The Al2014 alloy and Al2014-15 wt.% Al2O3 MMCs were in solution for 1 h at a temperature of 525 °C, quenched instantly in cold water, and then artificially aged for 10 h at a temperature of 175 °C. SEM and X-ray diffraction analyses were used to investigate the microstructure and dispersion of the reinforced Al2O3 particles in the composite and the base alloy Al2014. The obtained results indicated that the hardness, tensile and fatigue strength and wear resistance increased when an amount of Al2O3 particles was added, compared to the as-cast Al2014 alloy and it was observed that after subjecting the same composite samples to heat treatment, there was further enhancement in the mechanical and wear properties in the Al2014 matrix alloy and Al2014-15 wt.% Al2O3 composite samples.
21 September 2021 in Transactions of the Indian Institute of Metals