Nikolai I. Kakhidze

Mr. Nikolai I. Kakhidze

orcid

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
7 November 2019 in Metals
Verified
Journal Article
Open access
PDF file
IZIlya Zhukov
Ilya Zhukov
AKAlexander Kozulin
Alexander Kozulin
AKAnton Khrustalyov
Anton Khrustalyov
NKNikolai I. Kakhidze
Nikolai I. Kakhidze
KMKhmeleva Marina
Khmeleva Marina
AVAlexander Vorozhtsov
Alexander Vorozhtsov
This paper examines dispersion hardened alloys based on commercial-purity aluminum obtained by permanent mold casting with the addition of aluminum oxide nanoparticles. Ultrasonic treatment provides a synthesis of non-porous materials and a homogeneous distribution of strengthening particles in the bulk material, thereby increasing the mechanical properties of pure aluminum. It is shown that the increase in the alloy hardness, yield stress, ultimate tensile strength, and lower plasticity depend on the average grain size and a greater amount of nanoparticles in the alloy.

9 June 2022 in Metals
Verified
Journal Article
Open access
PDF file
AKAnton Khrustalyov
Anton Khrustalyov
NKNikolai I. Kakhidze
Nikolai I. Kakhidze
VPVladimir Platov
Vladimir Platov
IZIlya Zhukov
Ilya Zhukov
AVAlexander Vorozhtsov
Alexander Vorozhtsov
This paper investigates the impact of tungsten nanoparticles on the microstructure and mechanical properties of the Al-5Mg alloy. Tungsten concentrations of up to 0.5 wt.% led to a slight modification of the Al-5Mg alloy microstructure, and grain refinement occurred due to the inhibition of crystal growth along the boundaries. Dispersion hardening with tungsten nanoparticles made it possible to increase the ultimate strength by the Orowan mechanism with a simultaneous increase in the plasticity of the Al-5Mg alloy. An increase in the tungsten content to 0.8 wt.% made it possible to modify the microstructure of the Al-5Mg alloy, due to the formation of the Al12W phase and an increase in crystallisation centres. The modification of the microstructure, as well as dispersion strengthening by nanoparticles, led to a simultaneous increase in the yield strength, ultimate tensile strength, and ductility of the Al-5Mg alloy.

17 September 2020 in Russian Physics Journal
Verified
Journal Article
Closed access
PDF file
AKAlexander Kozulin
Alexander Kozulin
IZIlya Zhukov
Ilya Zhukov
AKAnton Khrustalyov
Anton Khrustalyov
NKNikolai I. Kakhidze
Nikolai I. Kakhidze
VVVladimir Danilovich Valikhov
Vladimir Danilovich Valikhov
AVAleksander Vorozhtsov
Aleksander Vorozhtsov

31 January 2023 in Tsvetnye Metally
Verified
Journal Article
Closed access
VVVladimir Danilovich Valikhov
Vladimir Danilovich Valikhov
IZI. A. Zhukov
I. A. Zhukov
NKNikolai I. Kakhidze
Nikolai I. Kakhidze
DTD. A. Tkachev
D. A. Tkachev
This paper looks at a composite material based on Al – Si alloy of grade AК9 that was produced by mechanical stirring and reinforced with 1 and 2 wt % of basalt fibres. The paper describes the results of a study that looked at the structure and phase composition of the basalt fibres introduced. It is shown that heat treating basalt fibres at the temperatures of up to 600 oC does not change their phase composition. The authors examine the microstructures of the initial cast alloy AK9 and the alloy reinforced with basalt fibres; look at the relationship between the structure obtained after introduction of basalt fibres and the physical and mechanical properties of the alloy; carried out a fractography study of the fracture surface in reinforced alloy specimens following a series of tensile tests. The authors analyzed how reinforcing effect is achieved when basalt fibres are introduced in the aluminium alloy AK9. The experimental data indicate that the introduction of basalt fibres in the aluminium matrix significantly enhances the mechanical performance of the alloy compared with the initial alloy AK9. Thus, the tensile strength and ultimate strength rise by 40 to 55 % compared with the initial alloy, whereas the hardness rises by 20 to 35 % depending on the weight fraction of basalt fibres in the alloy.This research was funded by the Ministry of Education and Science of the Russian Federation under Governmental Assignment No. FSWM-2020-0028. The studies (optical and electron microscopy, tensile tests, hardness and microhardness tests, study of phase composition) were carried out using the facilities of the Tomsk Regional Shared Knowledge Centre, a part of the National Research Tomsk State University. Support for the Centre is provided by the Ministry of Higher Education and Science of the Russian Federation under Grant No. 075-15-2021-693 (No. 13.ЦКП.21.0012).