A novel compact high-efficient circularly polarized conical horn antenna is realized with Wire Electrical Discharge Machining (EDM) technique operating at 300 GHz for 6G wireless communications is presented. The proposed antenna structure consists of three main components; a waveguide feed, a circular polarizer disk, and a conical horn. The waveguide feed is a standard WR-03 rectangular waveguide which feeds the whole structure. The circular polarizer disk is comprised of a crossed slot with unequal lengths which are perpendicular to each other. By adjusting the lengths of both slots, two orthogonal modes are excited in the antenna to produce circular polarization. The conical horn is mounted on the circular polarizer disk. The proposed antenna was designed and optimized using CST Microwave Studio and is validated experimentally by an inexpensive direct Wire-cutting EDM technique over the WM-860 frequency band. The fabricated circularly polarized horn antenna achieved a wide impedance bandwidth of 20 % from 270 GHz to 330 GHz with a reflection coefficient ≤ −15 dB. The measured results show that the 3 dB axial ratio of the fabricated antenna prototype has a bandwidth of 7 GHz from 309 GHz to 316 GHz with a minimum axial ratio of 1.15 dB at 312 GHz. The measured normalized radiation patterns show good agreement with simulated results for different frequencies in both the elevation and azimuth planes at broadside direction with good symmetry in both planes.
A low-profile high-gain fully-metallic circularly polarized (CP) Fabry-Perot cavity (FPC) antenna using laser cutting technology at 300 GHz is presented. The CP-FPC antenna consists of seven metallic layers arranged from the bottom to the top: a ground layer, an integrated stepped horn element (three layers), a coupling slots layer, a cavity layer, and an aperture-frequency selective surface (FSS) layer. The high gain and self-generation of circular polarization are made by using this FSS layer by introducing periodic hexagonal-shaped aperture in a thin metallic layer. The aperture-FSS layer is used to excite two orthogonal modes of equal in magnitude and in phase quadrature, thus obtaining the RHCP radiation. The proposed CP-FPC antenna structure achieves a measured peak RHCP gain of 16.5 dBic at 292 GHz. The antenna achieves a measured impedance bandwidth of 281- 305 GHz for the reflection coefficient less than -10 dB. The axial ratio (AR) bandwidth AR ≤3 dB is 5.12 GHz from 292.8 to 297.92 GHz. The fabricated CP-FPC antenna uses a low-cost laser cutting technique with a low-profile and an area of 2.6 mm ×2.6 mm ×1.24 mm. The experimental results confirm a good agreement between the simulation and the measurements.
Terahertz (THz) technology provides precise monitoring capabilities in dynamic environments, offering unique insights into insect habitats. Our study focuses on environmental monitoring of European honey bees (Apis mellifera) through a combination of measurements and simulations. Initially, the dielectric material properties of honey bee body parts are characterized across the spectral range of 1–500 GHz to collect heterogeneous empirical data. To extend the study, honey bee mockups made from polyamide 12 (PA12) and epoxy resin are employed and validated as effective substitutes for real bees through comparative scattering analyses. The research further explores radar cross-section (RCS), imaging, and spectral properties using advanced THz technologies, including resonant tunneling diodes (RTDs) operating at 250 GHz and THz time-domain spectroscopy (THz-TDS) for frequencies exceeding 250 GHz. High-resolution imaging, utilizing a 450 GHz bandwidth, captures intricate anatomical features of both real and 3D-printed bees, showcasing the potential of THz technology for detailed environmental monitoring. Finally, simulations at 300 GHz assess the dosimetry and feasibility of non-invasive, continuous monitoring approaches based on the heterogeneous honey bee model.
10 February 2016 in International Journal of Microwave and Wireless Technologies
In this paper a high gain aperture-coupled membrane antenna with a frequency selective surface (FSS) on a superstrate layer has been investigated. The base membrane antenna consists of a microstrip patch on the top of Roger RT-5580 substrate, supported by FR4 and is excited through an aperture fed by substrate-integrated waveguide (SIW). The CST Microwave Studio simulation results show that the proposed membrane structure has an impedance bandwidth (BW) of 8.85% from 75.97 to 82.96 GHz with a gain of 6.29 dBi at 79 GHz. To improve the gain, a superstrate layer is loaded above the membrane antenna, which increases the gain by 9.11 dB at 79 GHz. Furthermore by using FSS under superstrate layer, the gain is again increased by 2.5 dB. The total antenna structure provides a gain of 17.9 dBi at 79 GHz by keeping the same BW. The measured results are provided for the input matching (S11) only, the simulated results for the antenna gain and radiation patterns are obtained with the use of CST and are validated by using HFSS. The measured S11BW of the total antenna is from 75.57 to 84.18 GHz (10.89%), which is in agreement with the simulated results.
This communication presents a low-profile fully metallic high gain circularly polarized resonant cavity antenna, with a novel single-layer metasurface as superstrate operating at 300 GHz. The unit cell of the metallic metasurface layer consists of perforated grids of hexagonal and octagonal-shaped radiating apertures. The metasurface superstrate layer acts as a polarization convertor from linear-to-circular, which provides left-handed circularly polarized (LHCP) radiation. For simplicity and less design difficulty, a low cost laser cutting brass technology is proposed to design the antenna at sub-terahertz. The proposed circularly polarized resonant cavity antenna prototype has a low-profile planar metallic structure of volume 2.62.61.24. Experimental results validate the design concept. The antenna yields a measured LHCP gain of 16.2 dBic with a directivity of 16.7 dBic at 302 GHz. This proposed circularly polarized resonant cavity antenna finds potential application in 6G sub-terahertz wireless communications.
This paper presents the concept of substrate integrated waveguide (SIW) technology along with superstrate layer, which is used to design a high gain antenna for 79 GHz automotive short range radar (SRR) applications. The maximum gain of a single antenna with superstrate layer is 14.6 dBi at 79 GHz, which is higher than the gain of a classical 2 × 2 array. It is found that the gain of a single superstrate layer increases nearly 8.78 dB at 79 GHz over its SIW base antenna. The CST simulated 2:1 VSWR bandwidth with superstrate layer is from 75.9 GHz to 81 GHz (6.46 %). The antenna patterns are found to be broadside all over the frequency band of interest. Also the results are verified using another simulation software HFSS.