15 February 2017 in IEEE Transactions on Antennas and Propagation
This communication presents the design and experimental verification of a substrate integrated waveguide fed lens antenna for 79 GHz automotive radar applications. The proposed integrated lens antenna consists of a six layer cylindrical Luneburg lens illuminated by 17 source elements of substrate integrated waveguide fed by a planar log periodic dipole antenna array. The Luneburg lens is developed by using a unique foam material AirexR82 (ε r = 1.12), which is drilled and pressed to achieve the different dielectric constant needed to follow the index law inside the lens. The return loss and the radiation characteristics of the proposed integrated lens antenna are investigated and validated by measurements. A good agreement between the measured and simulated results is observed. The measured results confirm the beam scanning capability of the proposed integrated lens antenna for a wide scan angle of ±85° in azimuth plane having a maximum antenna gain of 15 dBi at 82.5 GHz and gain drop of less than 2.75 dB for the edge feeds. The estimated radiation efficiency of the antenna is found to be 67% at 82.5 GHz.
22 June 2020 in IEEE Access
A novel compact high-efficient circularly polarized conical horn antenna is realized with Wire Electrical Discharge Machining (EDM) technique operating at 300 GHz for 6G wireless communications is presented. The proposed antenna structure consists of three main components; a waveguide feed, a circular polarizer disk, and a conical horn. The waveguide feed is a standard WR-03 rectangular waveguide which feeds the whole structure. The circular polarizer disk is comprised of a crossed slot with unequal lengths which are perpendicular to each other. By adjusting the lengths of both slots, two orthogonal modes are excited in the antenna to produce circular polarization. The conical horn is mounted on the circular polarizer disk. The proposed antenna was designed and optimized using CST Microwave Studio and is validated experimentally by an inexpensive direct Wire-cutting EDM technique over the WM-860 frequency band. The fabricated circularly polarized horn antenna achieved a wide impedance bandwidth of 20 % from 270 GHz to 330 GHz with a reflection coefficient ≤ −15 dB. The measured results show that the 3 dB axial ratio of the fabricated antenna prototype has a bandwidth of 7 GHz from 309 GHz to 316 GHz with a minimum axial ratio of 1.15 dB at 312 GHz. The measured normalized radiation patterns show good agreement with simulated results for different frequencies in both the elevation and azimuth planes at broadside direction with good symmetry in both planes.
24 March 2020 in IEEE Access
A novel reconfigurable slotted leaky-wave antenna (LWA) based on substrate integrated waveguide (SIW) with a fixed-frequency beam-steering capability is presented in this paper. For a better compactness, this structure is based on SIW technology with rectangular slots fed by associated coupling with plated-through holes (PTH). It represents a new feeding method for etched slots in SIW antenna. Each via is loaded with a pin diode on both sides “Front & Back” of the waveguide. The pin diodes are tunable by adjusting the DC bias voltage, which eventually results in beam scanning at a fixed frequency around 27 GHz. An electronically controlled steerable SIW antenna is designed and it has been experimentally verified that the radiation angle varies from -33° to +33°.
30 August 2021 in IEEE Access
A low-profile high-gain fully-metallic circularly polarized (CP) Fabry-Perot cavity (FPC) antenna using laser cutting technology at 300 GHz is presented. The CP-FPC antenna consists of seven metallic layers arranged from the bottom to the top: a ground layer, an integrated stepped horn element (three layers), a coupling slots layer, a cavity layer, and an aperture-frequency selective surface (FSS) layer. The high gain and self-generation of circular polarization are made by using this FSS layer by introducing periodic hexagonal-shaped aperture in a thin metallic layer. The aperture-FSS layer is used to excite two orthogonal modes of equal in magnitude and in phase quadrature, thus obtaining the RHCP radiation. The proposed CP-FPC antenna structure achieves a measured peak RHCP gain of 16.5 dBic at 292 GHz. The antenna achieves a measured impedance bandwidth of 281- 305 GHz for the reflection coefficient less than -10 dB. The axial ratio (AR) bandwidth AR ≤3 dB is 5.12 GHz from 292.8 to 297.92 GHz. The fabricated CP-FPC antenna uses a low-cost laser cutting technique with a low-profile and an area of 2.6 mm ×2.6 mm ×1.24 mm. The experimental results confirm a good agreement between the simulation and the measurements.
10 September 2024 in IEEE Access
Insulations at high voltage (HV), whether in HVAC or HVDC systems, often encounter an unwanted partial discharge (PD) phenomenon. PD poses a potential danger to HV insulation and can eventually lead to equipment failures. Out of all electromagnetic (EM) sensing techniques for PD diagnosis, the ultra-high frequency (UHF) method has gained popularity as it allows non-invasive detection at varying distances from PD defects. The EM behavior of PD is significantly affected by the distance between a PD defect and a UHF sensor. This effect varies for different PD defects under different HV conditions. So, considering variable distances, there is a need to analyze EM characteristics of different PD phenomena at different HV conditions. To the best of our knowledge, for the first time, electromagnetic characteristics of different PD defects are experimentally investigated in this work by capturing PD signals from variable distances in both HVAC and HVDC conditions and individually validating their characteristics with EM radiation theories. For wirelessly capturing PD signals, a new UHF sensor is designed with a modified elliptical-shaped antenna on an FR-4 material. The fabricated sensor provides an average realized gain of about 3.66 dBi while covering more than 97% of the total UHF range for PD detection. Applying HVAC, HVDC+, and HVDC–, PDs from three defects (surface, void, free wire) are captured from 1–4 m distances. Interpreted results show that EM radiation in the UHF range from a PD defect is heavily impacted by its detection distance and defect formation despite applied voltage and other conditions being unchanged for the defect. This investigation is particularly beneficial to the variable distance-based PD diagnosis, such as PD localization and handheld PD detection at HVAC/HVDC open substations.
1 January 2026 in IEEE Access