Local austenization by local heating temperature control of blanks is one of the methods to obtain hot stamping parts with tailored properties. Resistance heating is a novel heating technology with high efficiency and rapid heating rate. In this paper, a heat transfer model was firstly developed to describe the steady temperature distribution of the blank during resistance heating. Then two resistance heating schemes to achieve tailored properties of hot stamping steel were investigated by experiments. One scheme is local resistance heating by adjusting the electrode position. And the other scheme is resistance heating with middle insulation. The results showed that the developed model could provide adequate accuracy in calculating the blank temperature field. For the local resistance heating, the percentage of high temperature region in heating zone was about 70 %. From the non-heating region to the middle heating region, hardness increased from 200 to 515 HV10. And the length ratio between high and low hardness regions could he controlled by adjusting electrode positions. For the resistance heating with middle insulation, a 340~360 HV10 medium hardness region with the length of 80mm was observed. The total length of transition hardness regions was about 60 mm. In summary, the local resistance heating scheme showed more advantages including shorter transition region and significant hardness difference.
The application of the quenching and partitioning (Q-P) process on advanced high-strength steels improves part ductility significantly with little decrease in strength. Moreover, the mechanical properties of high-strength steels can be further enhanced by the stepping-quenching-partitioning (S-Q-P) process. In this study, a two-stage quenching and partitioning (two-stage Q-P) process originating from the S-Q-P process of an advanced high-strength steel 30CrMnSi2Nb was analyzed by the simulation method, which consisted of two quenching processes and two partitioning processes. The carbon redistribution, interface migration, and phase transition during the two-stage Q-P process were investigated with different temperatures and partitioning times. The final microstructure of the material formed after the two-stage Q-P process was studied, as well as the volume fraction of the retained austenite. The simulation results indicate that a special microstructure can be obtained by appropriate parameters of the two-stage Q-P process. A mixed microstructure, characterized by alternating distribution of low carbon martensite laths, small-sized low-carbon martensite plates, retained austenite and high-carbon martensite plates, can be obtained. In addition, a peak value of the volume fraction of the stable retained austenite after the final quenching is obtained with proper partitioning time.
Traditional electric transmission line fittings, which are always manufactured from thick metal slabs, possess the disadvantage of heavy weight. In this study, a new type of electrical-connection-fitting, clevis-clevis component made of high-strength steel is developed to reduce weight, and a new hot-stamping process for multilayered sheets is proposed to manufacture the component efficiently. First, the structure of the new clevis-clevis component is designed, and the corresponding tool is developed. Second, a flat-tool heat transfer experiment is conducted. The influence of the number of layers and contact pressure on the cooling rate of each sheet is investigated. The optimizing number of layers and contact pressure for the multilayered-sheet, hot-stamping process are obtained. The optimal number of layers is two, and the optimal contact pressure is more than 20 MPa. The final microstructure of each sheet is fully martensitic, and the strength is about 1500 MPa. Finally, U-shaped, double-layer-sheet hot stamping is implemented to produce a typical electrical-connection-fitting, clevis-clevis component. The bearing capacity of a four-layered clevis-clevis is tested through numerical and experimental methods. The new connection-fitting clevis-clevis component exhibits a high load capacity of 280 kN. Compared with that of the traditional component, the weight of the new component is reduced by 60%.
During the solution heat treatment (SHT) process of aluminum alloys, precipitates dissolve into the matrix. To predict the dissolution time, modeling of isothermal dissolution of precipitates in 6061 aluminum alloy during SHT was conducted. A precipitate dissolution model was established, and the flowchart of the modeling was designed as well. Then the explicit finite-difference method was employed to solve the dissolution model, and the mobile nodes method was used to deal with the moving interface. The simulation was based on real precipitates in 6061, and SHT experiments were conducted to validate the numerical model. The simulation results showed that the isothermal dissolution time of precipitates in 6061-T6 aluminum alloy at 560 °C is 11.6856 s. The dissolution time in the simulation was close to the experimental results, with an error of 16.7%, indicating that the modeling in this study was fairly reasonable and accurate. The error was caused by many factors, and the model should be improved.
It is an effective means to make automotive structural parts of medium manganese steel, which is highly plastic, to achieve lightweight, but the martensite phase change occurs in the formation of manganese steel, which changes its mechanical properties and makes it difficult to evaluate the service performance of the parts. Therefore, the peak of Barkhausen noise (MBN) signal was studied, and the relationship curve based on MBN signal is obtained. According to the design stamping experiment of U-shaped parts of the same material, XRD and MBN test and verify the stamping steel properties respectively.