Application of the hot stamping process on heat-treatable aluminum alloys effectively solves the problems of large springback and poor ductility during forming at room temperature, which expands the range of applications of aluminum alloys in the transportation industry. Sheet heating plays an important role in the hot stamping process, and increasing the heating rate can improve the hot stamping efficiency to some extent. In this paper, the feasibility of applying contact heating techniques with higher heating rates in the hot stamping process was studied. A contact heating device was designed, and the temperature distribution of the device contact surface was observed. Furthermore, the heating characteristics of 7075 aluminum alloy sheets during the contact heating process were explored by experiments and finite element simulation. Finally, the rapid solution treatment of aluminum alloy was carried out with a contact heating device, which was compared with the furnace heating solution treatment. The experimental and simulation results indicate that the device contact surface has a relatively uniform temperature distribution, and the aluminum alloy sheets can be heated to close to the set temperature in 15 s using contact heating techniques. Meanwhile, the rapid solution treatment of aluminum alloy sheets can be achieved within 15–20 s by contact heating techniques, obtaining superior mechanical properties. This suggests that the contact heating process can be used for rapid heating and rapid solution treatment of aluminum alloy sheets in hot stamping process.
The application of the quenching and partitioning (Q-P) process on advanced high-strength steels improves part ductility significantly with little decrease in strength. Moreover, the mechanical properties of high-strength steels can be further enhanced by the stepping-quenching-partitioning (S-Q-P) process. In this study, a two-stage quenching and partitioning (two-stage Q-P) process originating from the S-Q-P process of an advanced high-strength steel 30CrMnSi2Nb was analyzed by the simulation method, which consisted of two quenching processes and two partitioning processes. The carbon redistribution, interface migration, and phase transition during the two-stage Q-P process were investigated with different temperatures and partitioning times. The final microstructure of the material formed after the two-stage Q-P process was studied, as well as the volume fraction of the retained austenite. The simulation results indicate that a special microstructure can be obtained by appropriate parameters of the two-stage Q-P process. A mixed microstructure, characterized by alternating distribution of low carbon martensite laths, small-sized low-carbon martensite plates, retained austenite and high-carbon martensite plates, can be obtained. In addition, a peak value of the volume fraction of the stable retained austenite after the final quenching is obtained with proper partitioning time.
To enhance the performance of ultra-high voltage power fittings in severe weather conditions without altering their current structure, the high-strength and toughness aluminum alloys were rationally selected to study the optimization of the die-casting process. This approach aims to improve the overall longevity and function of the power fittings in extreme climates. First of all, the propose of this study is to use the material’s strength–toughness product (STP) concept to evaluate the material stability of the power fitting impact resistance and fatigue toughness in order to determine the appropriate material selection. Secondly, the location of the mold’s sprue and gate was optimized through finite element simulation to prevent gas volume and flow defects during the casting process. This improves the material’s toughness and anti-fatigue failure characteristics of the product. Then, vacuum equipment and a vacuum valve auxiliary system were added based on the existing die-casting machine, and the mold structure was optimized to enable the vacuum die-casting process. Finally, a water-based boron nitride environmentally friendly mold release agent was used to solve demolding difficulties with an A356 aluminum alloy and improve mold lubrication and surface quality. The production of quad-bundled spacers using A356 and vacuum die casting has resulted in parts with a tensile strength of at least 250 MPa and an elongation of no less than 7%. This improvement has laid a foundation for enhancing the operational reliability of existing overhead transmission line fittings.
During the solution heat treatment (SHT) process of aluminum alloys, precipitates dissolve into the matrix. To predict the dissolution time, modeling of isothermal dissolution of precipitates in 6061 aluminum alloy during SHT was conducted. A precipitate dissolution model was established, and the flowchart of the modeling was designed as well. Then the explicit finite-difference method was employed to solve the dissolution model, and the mobile nodes method was used to deal with the moving interface. The simulation was based on real precipitates in 6061, and SHT experiments were conducted to validate the numerical model. The simulation results showed that the isothermal dissolution time of precipitates in 6061-T6 aluminum alloy at 560 °C is 11.6856 s. The dissolution time in the simulation was close to the experimental results, with an error of 16.7%, indicating that the modeling in this study was fairly reasonable and accurate. The error was caused by many factors, and the model should be improved.
The hot stamping technology is widely used because of the good formability, lower forming force, less spring back and high strength parts obtained. However, with the consistently increasing requirements for safety performance improvement, the fully martensitic hot stamped parts cannot meet the new requires, which consist high strength and energy absorbing. The compatibility of mechanical properties and safety performance of vehicle parts such as b-pillar has been proposed that different mechanical properties are needed in different regions of the same parts, namely tailored properties. Microstructure of hot stamped parts with tailored properties consist of multiphase, so in this paper, experiments and simulation have been performed to study the constitutive and fracture models of hot stamped parts with multiphase. The digital image correlation (DIC) technology was used to measure the strain over the whole specimen and the elastoplasticity constitutive models of martensite, bainite and ferrite/pearlite have been obtained. By combining the experiments and numerical simulation, the parameters of fracture model have been optimized, which are very hardly to be determined using only experiments. The constitutive and fracture models of multiphase has been obtained using the liner-mixture rule.
This experiment devised a set of cold-hot partitioning molds for preparing U-shaped components made of 22MnB5 with variable strength. Employing a hot stamping process, the molds were set at temperatures of 400℃, 450℃, and 500℃ respectively. Samples were taken from the soft and hard regions of the fabricated components, and the transition zone length was determined through hardness testing. The mechanical properties of the hard and soft regions were assessed via uniaxial tensile tests, yielding the corresponding engineering stress-strain curves, tensile strength, and elongation at fracture. Microstructural observations were conducted using SEM to summarize the influence of mold temperatures on the mechanical properties of the produced components.