This paper presents the testing of the durability of concrete where a part of cement was replaced with ground panel cathode ray tube glass (CRT) finer than 63 µm. The percentage of cement replaced with glass is 5%, 10%, 15%, 20%, and 35%, by mass. The highest percent share of mineral admixtures in CEM II (Portland-composiste cement) cement was chosen as the top limit of replacement of cement with glass. In terms of the concrete durability, the following tests are performed: freeze-thaw resistance, freeze-thaw resistance with de-icing salts-scaling, resistance to wear according to the Böhme test, sulfate attack resistance, and resistance to penetration of water under pressure. A compressive strength test is performed, and shrinkage of concrete is monitored. In order to determine the microstructure of concrete, SEM (Scanning Electron Microscopy) and EDS (Energy Dispersive X-ray Spectroscopy) analyses were performed. The obtained research results indicate that the replacement of a part of cement with finely ground CRT glass up to 15% by mass has a positive effect on the compressive strength of concrete in terms of its increase without compromising the durability of concrete. The results obtained by experimental testing unequivocally show that concrete mixtures made with partial replacement (up to 15%) of cement with finely ground CRT glass have the same freeze-thaw resistance, resistance to freeze/thaw with de-icing salt, resistance to wear by abrasion, and resistance to sulfate attack as the reference concrete. In terms of environmental protection, the use of CRT glass as a component for making concrete is also very significant.

The potential to use waste glass, including cathode ray tube (CRT) glass, for making new products or as an admixture to existing ones is being intensively investigated. This kind of research intensified particularly in the period after CRT TV sets and computer monitors were replaced in the market by the advanced technology of thin film transistor (TFT) and liquid crystal display (LCD) screens. Cathode ray tube glass represents a considerable part of electronic waste (e-waste). E-waste globally increases at a far higher rate than other solid waste materials. There is a possibility to recycle cathode ray tube glass and use it in the construction industry. This paper shows the test results of physical and mechanical properties of blocks and paving flags. The reference specimen was made with quartz sand, while the other product employed a combination of quartz sand and ground panel cathode ray tube glass. The glass was ground to the fraction 0.25/1.00 mm, which corresponds to quartz sand fineness. The following tests were performed: shape and dimensions, resistance to freeze/thaw and de-icing salts, water absorption, splitting tensile strength and tensile strength by bending. Special attention was paid to the tests of Böhme wear resistance, slip resistance of the top surface of CRT products using a pendulum, radioactivity and leaching. The texture of the experimental concrete products was observed by SEM (scanning electron microscopy) and analyzed. The results obtained by experimental testing unequivocally show that CRT glass can successfully be used for making concrete blocks and paving flags.

The topic of this paper is experimental and numerical analysis of the impact strength of unreinforced concrete slabs. Impact strength of concrete is significant in case of some accidental loads during exploitation. Impact strength can be determined experimentally, using Drop-weight test, Charpy test, Projectile impact test, Explosive test, etc. In this research, a numerical model for determining the impact strength of concrete slabs based on Finite element method (FEM) and high-end engineering software has been proposed. Modelling approach to this problem was applying the Explicit dynamics FEM analysis. Thereat, two different existing material models for concrete were enforced: Concrete damage plasticity model – CDP (implemented in ABAQUS/Explicit software), and the Riedel-Hiermaier-Thoma model – RHT (implemented in ANSYS Workbench software). Analysis parameters for both material models, necessary as input data, have been determined through a series of FEM analyses and validated by performed experiments, using drop-weight test. Results of the numerical analyses have been compared with the experimental ones, as well as mutually. Advantages and drawbacks of both material models are highlighted, as well as the reliability of the proposed numerical models. The proposed numerical FE models, confirmed by experiments, can be successfully used for determining impact strength of concrete slabs in further research.

The demand of the contemporary society for renewable energy sources lead to the increase of the bio-power plants. Accordingly, the amount of ash generated by burning the biomass is increased, and its disposal becomes a large...

The electronic and electric waste (e-waste) quantities have been sharply increasing since the beginning of the 21st century. A significant portion of e-waste is composed of glass originating from the cathode ray tubes of the TV-set screens and computer monitors (CRT glass) which, due to the complexity of the recycling process and its chemical composition is very hazardous and represents a huge environmental problem. One of the modes of recycled CRT glass application is for making of self-compacting concrete (SCC). The paper investigated various properties of fresh and hardened SCC where CRT glass played the role of powdery mineral admixture. SCC made in such a way, with satisfactory physical-mechanical characteristics is suitable for production of various precast concrete elements. In order to monitor the durability of experimental concrete in actual conditions, several curbs were experimentally placed in the course of reconstruction of a street in Nis.

This paper presents the application of a hybrid approach for damage localization in concrete plates of arbitrary geometric shapes and a constant thickness. The hybrid algorithm utilizes fast discrete wavelet transformation, energy approach and time of flight criteria for the purpose of the localization of single- and multi-damage problems inside or on the periphery of concrete plates. A brief theoretical background of the hybrid method as well as numerical procedures for modeling the piezoelectric smart aggregate and ultrasonic wave propagation are presented. Experimental and numerical verification of the damage localization were performed on square samples/models with one or two damages and with 16 positions of piezoelectric smart actuator/sensor aggregates. After the verification of the hybrid method, a numerical simulation was performed on models with one or two damages for plates of arbitrary geometric shapes. Based on the obtained results, it was concluded that the proposed method can be applied to damage localization in concrete plates of arbitrary geometric shapes. The presented method and numerical procedure can be further used in research through varying the geometry, number and position of damages as well as the number and position of piezoelectric smart aggregates.