Patrick Consul

Mr. Patrick Consul

orcid

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
24 July 2021 in Polymers
Verified
Journal Article
Open access
PDF file
PCPatrick Consul
Patrick Consul
KBKai-Uwe Beuerlein
Kai-Uwe Beuerlein
GLGenc Luzha
Genc Luzha
KDKlaus Drechsler
Klaus Drechsler
Additive manufacturing by material extrusion such as the widespread fused filament fabrication is able to improve 3D printed part performance by using short fiber reinforced composite materials. Fiber alignment is critical for the exploitation of their reinforcing effect. This work investigates the influence extrusion parameters have on the fiber alignment by conducting set of experiments on the process parameters determining whether the flow under the nozzle is convergent or divergent. A strong impact of flow conditions during extrusion line shaping on the fiber alignment is observed and two extremes are tested which show a large difference in strength, stiffness and strain at break in tensile testing along the extrusion lines. From highest to lowest fiber alignment, strength is reduced by 41% and stiffness by 54%. Fiber misalignment also leads to inhomogeneous strain fields in the layers when tested perpendicular to the extrusion lines. It is demonstrated that material flow after the nozzle has a high impact on the material properties of short fiber reinforced 3D printed parts and needs to be considered in process design.

19 December 2020 in Polymer International
Verified
Journal Article
Open access
PDF file
PCPatrick Consul
Patrick Consul
ACAdam Chaplin
Adam Chaplin
NTNevine Tagscherer
Nevine Tagscherer
SZSwen Zaremba
Swen Zaremba
KDKlaus Drechsler
Klaus Drechsler
Fusion bonding theory is applied to the additive manufacturing process to predict the strength developed across the interface between the deposited layers in material extrusion based large‐scale additive manufacturing. Relaxation times were determined through rheology investigations of the neat polymers and were extrapolated across the entire process temperature range to estimate the required welding times for optimal bond formation. For the calculation of bond formation during cooling from the melt, the semicrystalline polyaryletherketone is considered amorphous until the onset of crystallization which is determined by recreating the process thermal history in DSC measurements. A significant improvement in bond development during additive manufacturing is achieved through the use of specifically designed polymers with slower crystallization kinetics. Both in small‐scale additive manufacturing, achieving full bonding, and in large‐scale additive manufacturing, they achieve significantly higher interlaminar strength than the reference material, validated by three‐point bending. A very good match between the estimated degree of bonding and the tested strength of upright printed specimens in three‐point bending was found. While the fusion bonding model calculates a degree of bonding of 42.07%, mechanical testing showed 42.54% of the bulk flexural strength. The study outlines a procedure to evaluate materials for additive manufacturing by material extrusion based on small material samples to shorten and improve the process development. © 2020 The Authors. Polymer International published by John Wiley & Sons Ltd on behalf of Society of Industrial Chemistry

14 July 2021 in Polymer Composites
Verified
Journal Article
Open access
PDF file
NTNevine Tagscherer
Nevine Tagscherer
PCPatrick Consul
Patrick Consul
IKIngo Leonard Kottenstedde
Ingo Leonard Kottenstedde
HLHouyem Latiri
Houyem Latiri
SZSwen Zaremba
Swen Zaremba
KDKlaus Drechsler
Klaus Drechsler
Fusion bonding is understood to be the decisive mechanism for the interlayer strength in extrusion additive manufacturing. This study links the characteristic temperatures of semicrystalline thermoplastics, namely, PA6 with 40% carbon fibers, to the bond formation in respect to real‐world processing conditions. Based on theoretical investigations, a process window is proposed for bonding to occur without polymer degradation. This range from the glass transition to the initial degradation temperature was determined through differential scanning calorimetry and thermogravimetric analysis. A second process window for optimal bonding is proposed from the extrapolated onset crystallization temperature, , to the melt temperature, . The validation of these process windows was conducted by bending tests according to DIN EN 178. was confirmed as the upper limit, with the part's geometric integrity compromised at higher temperatures. had to be refuted as lower limit as no discrete reduction in bond strength was determined in alignment with . Authors suggest the lower limit is defined by the lowest substrate temperature to lead to interface temperatures above the onset of melt temperature. By utilizing thermal analyses, less time and resources are required to detemine a suitable process window for extrusion additive manufacturing.

21 August 2024 in Polymers
Verified
Journal Article
Open access
PDF file
PCPatrick Consul
Patrick Consul
MFMatthias Feuchtgruber
Matthias Feuchtgruber
BBBernhard Bauer
Bernhard Bauer
KDKlaus Drechsler
Klaus Drechsler
Additive Manufacturing (AM) enables the automated production of complex geometries with low waste and lead time, notably through Material Extrusion (MEX). This study explores Large Format Additive Manufacturing (LFAM) with carbon fiber-reinforced polyaryletherketones (PAEK), particularly a slow crystallizing grade by Victrex. The research investigates how extrusion parameters affect the mechanical properties of the printed parts. Key parameters include line width, layer height, layer time, and extrusion temperature, analyzed through a series of controlled experiments. Thermal history during printing, including cooling rates and substrate temperatures, was monitored using thermocouples and infrared cameras. The crystallization behavior of PAEK was replicated in a Differential Scanning Calorimetry (DSC) setup. Mechanical properties were evaluated using three-point bending tests to analyze the impact of thermal conditions at the deposition interface on interlayer bonding and overall part strength. The study suggests aggregated metrics, enthalpy deposition rate and shear rate under the nozzle, that should be maximized to enhance mechanical performance. The findings show that the common practice of setting fixed layer times falls short of ensuring repeatable part quality.

18 July 2024 in Journal of Thermoplastic Composite Materials
Verified
Journal Article
Open access
MFMatthias Feuchtgruber
Matthias Feuchtgruber
JHJohn Holmes
John Holmes
SSSilvano Sommacal
Silvano Sommacal
MSMaximilian Strobel
Maximilian Strobel
FGFlorian Gehringer
Florian Gehringer
KDKlaus Drechsler
Klaus Drechsler
In this work, we investigated the effect of plain woven carbon fiber tape embedded in each layer of an additively manufactured part on the coefficient of thermal expansion (CTE) and compared it to conventionally printed parts. Current advancements in Additive Manufacturing enable cost-efficient 3D printing of composite tools. However, these tools do not yet offer a low CTE comparable to Invar, necessary for producing aerospace-quality composite parts. Using the novel Advanced Tape Layer Additive Manufacturing process, the tape is placed on top of the bead immediately after extruding the short fiber-reinforced material. The samples are compared to Material Extrusion specimens from a Large Format Additive Manufacturing System. A lower CTE was achieved within the printing plane. Micro-computed tomography images correlate the preferential orientation of short fibers with measured CTE values. The CTE modification can match the part CTE to the tool CTE and therefore optimize the quality of manufactured parts.

28 October 2026 in Journal of Materials Processing Technology
Verified
Journal Article
Open access
TWTing Wang
Ting Wang
PCPatrick Consul
Patrick Consul
BBBenno Böckl
Benno Böckl
TWThomas Wettemann
Thomas Wettemann
KDKlaus Drechsler
Klaus Drechsler