In this work, tungsten carbide (WC) and hexagonal boron nitride ( h BN) have been used as a filler in epoxy resin to a novel composite to enhance the radiation attenuation properties. Four composites were obtained by using various WC/ h BN concentrations. The linear attenuation coefficients of all composites were measured experimentally. At 662keV, the 7W1B composite (%20 epoxy, %40 h BN and %40 WC) had the lowest radiation shielding parameters, including half value length, tenth value layer, and mean free path with the 7.73 cm, 3.356 cm and 2.326 cm values, respectively. Thermal neutron absorption increased proportionally with h BN content, reaching 0.575 cm⁻¹, while fast neutron absorption ranged from 0.0522 to 0.1232 cm⁻¹. Experimental radiation shielding results are supported by theoretical results. In addition, thermal and fast neutron absorption values of the materials were calculated. Thermal neutron absorption values (Σₐ) increased from 0.344 to 0.575 cm⁻¹ with rising h BN content, confirming the contribution of boron-10 isotope in neutron shielding. Similarly, fast neutron absorption values ranged from 0.0522 to 0.1232 cm⁻¹, further supporting the hybrid composite’s potential in mixed radiation environments Mechanical testing revealed that excessive filler loading led to reduced flexural strength due to agglomeration, while balanced compositions achieved better dispersion and structural performance. Thermal analysis indicated enhanced heat conduction with increased WC content. These results demonstrate that WC– h BN–epoxy composites offer a lightweight, efficient, and tunable alternative for radiation shielding in nuclear, aerospace, and defense applications.
Colorectal cancer (CRC), breast cancer, and chronic myeloid leukemia (CML) are life-threatening malignancies worldwide. Although potent therapeutic and screening strategies have been developed so far, these cancer types are still major public health problems. Therefore, the exploration of more potent and selective new agents is urgently required for the treatment of these cancers. Quinones represent one of the most important structures in anticancer drug discovery. We have previously identified a series of quinone-based compounds (ABQ-1-17) as anti-CML agents. In the current work, ABQ-3 was taken to the National Cancer Institute (NCI) for screening to determine its in vitro antiproliferative effects against a large panel of human tumor cell lines at five doses. ABQ-3 revealed significant growth inhibition against HCT-116 CRC and MCF-7 breast cancer cells with 2.00 µM and 2.35 µM GI50 values, respectively. The MTT test also showed that ABQ-3 possessed anticancer effects towards HCT-116 and MCF-7 cells with IC50 values of 5.22 ± 2.41 μM and 7.46 ± 2.76 μM, respectively. Further experiments indicated that ABQ-3 induced apoptosis in both cell lines, and molecular docking studies explicitly suggested that ABQ-3 exhibited DNA binding in a similar fashion to previously reported compounds. Based on in silico pharmacokinetic prediction, ABQ-3 might display drug-like features enabling this compound to become a lead molecule for future studies.
A wide variety of thermal interface materials (TIMs) used in the electronics semiconductor industry, but heat dissipation is still a problem. Meeting this challenge requires the development of new polymer-based composite materials with improved thermal conductivity. In this study, carbon fiber (CF)/Silicon carbide (SiC) hybrid filler-loaded polypropylene (PP) matrix composites were produced. Thermal properties of composites were investigated by the simultaneous differential thermal analysis, differential scanning calorimeter and thermal conductive measurement system. The mechanical properties of composites were measured by dynamic mechanic analysis and universal mechanical analysis test systems. The molecular structure changes and crystallinity of composites were analyzed by X-ray diffraction analysis. The composites microstructure was identified by scanning electron microscopy technique. The electrical conductivity of the composites investigated with the electrical conductivity measurement technique. The addition of CF into the SiC particles improved thermal degradation and mechanical properties of composites according to only SiC loaded PP matrix. The mixture of 3% CF and 47% SiC particle by weight into the PP matrix improved the thermal conductivity of composites almost 40% than the 50% SiC loaded PP. The viscoelastic properties and the durability of the composites increased with the CF addition.