Battery Electric Vehicles (BEVs) are advocated due to their environmental benign characteristic. However, the long charging time and the degradation caused by fast charging impedes their further popularization. Extensive research has been carried out to optimize the charging process, such as minimizing charging time and aging, of Lithium-ion Batteries (LIBs). Motivated by this, a comprehensive review of existing Charging Optimization (ChgOp) techniques is provided in this paper. Firstly, the operation and models for LIBs are explained. Then, unexpected side effects especially for the aging mechanism of LIB associated with unregulated fast charging are scrutinized. This provides a solid theoretical foundation and forms the optimization problem. Following this endeavor, the general framework with critical concerns for ChgOp system design is overviewed. Within this horizon, the state-of-the-art ChgOp techniques, clustered into open- and close-loop categories, are reviewed systematically with their respective merits and shortcomings discussed. Finally, the development of an emerging charging control protocol with both real-time affordability and degradation consciousness is further discussed as an open outlook.
30 November 2018 in IEEE Transactions on Power Electronics
Temperature Sensitive Electrical Parameters (TSEPs) are promising for measurement of the IGBT chip temperature, Tchip. Many TSEPs have been proposed in the literature and most require current sensors, and convoluted hardware and data processing, which are associated with increased complexity and cost. In this letter, a new TSEP is proposed called pre-threshold TSEP, V$_{GE(pre-th)}$. V$_{GE(pre-th)}$ requires only a voltage sensor and a counter. Besides less hardware requirement, V$_{GE(pre-th)}$ does not suffer from self-heating – a problem that most TSEPs encounter. This letter presents the operation of V$_{GE(pre-th)}$ with the help of simulation. Experimental tests on a 3.3kV, 800A IGBT were conducted to characterize V$_{GE(pre-th)}$. It is shown that the new TSEP proposed has a sensitivity of -2.2mV/°C.
8 January 2020 in IEEE Transactions on Power Electronics
Multi-chip Insulated Gate Bipolar Transistor (mIGBT) power modules (PMs) degrade over power cycling. Bond wire lift-off is one of the major failure modes. This paper presents a technique to diagnose bond wire lift-off by analyzing the on-state voltages across collector and emitter terminals and the voltages across collector and Kelvin emitter terminals. The proposed method can indicate the first lift-off out of 37 bond wires in a mIGBT. The main novelty of the proposed technique is that it can locate the chip that has bond wire lift-off(s). The paper describes the proposed technique in detail and shows results and discussions based on practical tests which are carried out on two mIGBT PMs with different packages.
28 December 2020 in IEEE Journal of Emerging and Selected Topics in Power Electronics
Temperature Sensitive Electrical Parameters (TSEPs) are used to determine the chip temperature of a single-chip IGBT power module by measuring one electrical device parameter. Commonly, most TSEPs have a linear relationship between the chip temperature and the electrical parameter. Like any sensor, preferred attributes of TSEPs include good accuracy, linearity, and sensitivity. For multichip Insulated Gate Bipolar Transistors (mIGBTs) modules, these can only be achieved when all chips have the same temperature. Equal chip temperatures among different semiconductor chips can be achieved when placing mIGBTs in environmental chambers to produce a homogeneous temperature distribution (HTD). In real applications, however, mIGBTs are power cycled and are exposed to inhomogeneous temperature distribution (ITD) where temperature differences exist between chips. Consequently, measuring one electric parameter only cannot represent each chip temperature which impacts the TSEP sensitivity, linearity, and accuracy. This paper compares the performance of ten TSEPs applied to a mIGBT module operating at HTD and ITD conditions in order to determine which TSEPs are most suitable for mIGBTs in real applications.
8 December 2023 in IEEE Transactions on Power Electronics
The heat transfer of power devices has the characteristics of multi-timescale. However, the traditional thermal network model is difficult to predict the temperature information of power devices at multi-timescale accurately. This paper proposes a multi-timescale thermal network model for power devices, with MOSFET as an example. First, we establish a finite element model for temperature calculation of power devices and then reduce the order of the finite element model based on the proper orthogonal decomposition (POD) algorithm. The reduced order model is converted into an equivalent circuit model by the node voltage method and integrated into the circuit simulation software. To demonstrate its general applicability, this paper also establishes thermal network models for both IGBT and SiC MOSFET devices, validates the multi-time scale thermal network models through ANSYS/Transient Thermal software and experiments. The temperature calculation results of the three power devices all indicate that the proposed multi-time scale thermal network model can calculate the temperature of power devices faster than ANSYS/Transient Thermal model, and has less than 5% error under test conditions. This paper is accompanied by a video demonstrating a comparison of the computational speed of the multi-timescale thermal network model with a finite element model. Finally, a case study of junction temperature calculation in a Buck converter is presented to illustrate the application method of the thermal network model.