Chao Voon Samuel Lim

Dr. Chao Voon Samuel Lim

Monash University, Melbourne, Australia
orcid

Research Focus & Metrics

Academic Career Length

13Years (2014-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 January 2022 in Journal of Materials Science & Technology
Verified
Journal Article
Closed access
YLYang Liu
Yang Liu
CLChao Voon Samuel Lim
Chao Voon Samuel Lim
CDChen Ding
Chen Ding
AHAijun Huang
Aijun Huang
MWMatthew Weyland
Matthew Weyland

1 April 2021 in International Journal of Mechanical Sciences
Verified
Journal Article
Closed access
MLMeng Li
Meng Li
CLChao Voon Samuel Lim
Chao Voon Samuel Lim
RZRuiping Zou
Ruiping Zou
XAXizhong An
Xizhong An
DWDefeng Wang
Defeng Wang

2 November 2023 in Sustainability
Verified
Journal Article
Open access
PDF file
TKTejas Koushik
Tejas Koushik
HSHaopeng Shen
Haopeng Shen
WKWen Hao Kan
Wen Hao Kan
MGMu Gao
Mu Gao
JYJunlan Yi
Junlan Yi
AHAijun Huang
Aijun Huang
Laser powder bed fusion (LPBF) is an outstanding additive manufacturing (AM) technology that can enable both complicated geometries and desired mechanical properties in high-value components. However, the process reliability and cost have been the obstacles to the extensive industrial adoptions of LPBF. This work aims to develop a powder recycling procedure to reduce production cost and minimize process uncertainties due to powder degradation. We used a recycle index (R) to reuse Ti-6Al-4V powder through 10 production cycles. Using this recycle index is more reasonable than simply replying on recycle numbers as it incorporates the powder usage history. A recycling procedure with simple virgin powder top-up can effectively mitigate powder degradation and maintain stable powder properties, chemical compositions, and tensile properties. The experimental finding points to a sustainable recycling strategy of Ti alloy powders with minimal material waste and without noticeable detriment to observed mechanical performance through LPBF production cycles.

24 November 2024 in Virtual and Physical Prototyping
Verified
Journal Article
Open access
CSChun Kit Sit
Chun Kit Sit
Yunlong TangYunlong Tang
Yunlong Tang
LCLouis Ngai Sum Chiu
Louis Ngai Sum Chiu
CLChao Voon Samuel Lim
Chao Voon Samuel Lim
YZYuman Zhu
Yuman Zhu
AHAijun Huang
Aijun Huang

12 February 2014 in Journal of Micro and Nano-Manufacturing
Verified
Journal Article
Closed access
PDF file
Ehsan GhassemaliEhsan Ghassemali
Ehsan Ghassemali
Ming Jen TanMing Jen Tan
Ming Jen Tan
CLChao Voon Samuel Lim
Chao Voon Samuel Lim
CWChua Beng Wah
Chua Beng Wah
Jarfors AndersJarfors Anders
Jarfors Anders
Friction effects during a progressive microforming process for production of micropins of various diameters were experimentally investigated and were analytically modeled, using a hybrid friction model. The response surface method and ANOVA analysis were used to generalize the findings for various pin diameters. Besides, it was shown that to get an accurate result in simulation, the friction model must be considered locally instead of a global friction model for the whole process. The effect of friction factor on the final micropart dimensions (the effect on the instantaneous location of the neutral plane) and the forming pressure were investigated. The results showed a reduction in the friction factor as die diameter increased. Following that, the optimum frictional condition to obtain the highest micropart aspect ratio was defined as the maximum friction on the interface between the die upper surface and the punch surface, together with a minimum friction inside the die orifice.

11 October 2023 in Additive Manufacturing
Verified
Journal Article
Closed access
QWQiong Wu
Qiong Wu
CQChuang Qiao
Chuang Qiao
YWYuhang Wu
Yuhang Wu
ZLZhe Liu
Zhe Liu
XLXiaodan Li
Xiaodan Li
CLChao Voon Samuel Lim
Chao Voon Samuel Lim