TianQin is a future space-based gravitational wave (GW) observatory targeting the frequency window of 10−4–1 Hz. A large variety of GW sources are expected in this frequency band, including the merger of massive black hole binaries, the inspiral of extreme/intermediate mass ratio systems, stellar-mass black hole binaries, Galactic compact binaries, and so on. TianQin will consist of three Earth orbiting satellites on nearly identical orbits with orbital radii of about 105 km. The satellites will form a normal triangle constellation whose plane is nearly perpendicular to the ecliptic plane. The TianQin project has been progressing smoothly following the ‘0123’ technology roadmap. In step ‘0’, the TianQin laser ranging station has been constructed and it has successfully ranged to all the five retro-reflectors on the Moon. In step ‘1’, the drag-free control technology has been tested and demonstrated using the TianQin-1 satellite. In step ‘2’, the inter-satellite laser interferometry technology will be tested using the pair of TianQin-2 satellites. The TianQin-2 mission has been officially approved and the satellites will be launched around 2026. In step ‘3’, i.e. the TianQin-3 mission, three identical satellites will be launched around 2035 to form the space-based GW detector, TianQin, and to start GW detection in space.
A high-frequency signal generator based on direct digital synthesizer (DDS) and field-programmable gate array (FPGA) is presented. The FPGA provides the controlling time sequence for the DDS, which has a highest output frequency of 1.4 GHz and a frequency resolution of 190 pHz. At an output frequency of 1.2 GHz, the measured phase noise, including the contribution of the reference clock, is −65 dBc/Hz@1 Hz, while the intrinsic phase noise is −82 dBc/Hz@1 Hz. Time delay of the DDS is measured to be less than 150 ns. The signal generator is used to drive an acousto-optic modulator, and the rise time due to the whole link is 24 ns. The developed signal generator can be used in many precision measurement experiments in the fields of atomic, molecular, and optical physics.
The space-based gravitational wave detection mission, TianQin, requires high-level synchronization between independent clocks of all spacecrafts to extract the gravitational wave signals. It is necessary to measure the inter-spacecraft relative clock jitter based on laser phase-sideband clock transfer. The main challenge is the tracking and locking of clock sideband beatnote signals with low signal-to-noise ratio and frequency variation. In this paper, a systematic scheme of inter-spacecraft clock jitter readout is reported. The requirement of the clock transfer link for TianQin based on the time-delay interferometry algorithm is derived. A bi-directional laser interferometer system with a transmission optical power below 1 nW and a time delay of ∼50 µs is built up to demonstrate the weak-light clock transfer. In this scheme, frequency modulation is performed on the laser to simulate the inter-spacecraft Doppler frequency shift and its variation. Based on electrical and optical clock transfer comparison experiments, it is demonstrated that the GHz frequency synthesizer is the main noise source below the 50 mHz frequency range. The residual clock jitter noise introduced by the optical transfer link is below 40 fs/Hz1/2 above the 6 mHz frequency range, and the fractional frequency instability is less than 6.7 × 10−17 at 1000 s, which meets the requirement of the TianQin mission. Ultimately, The carrier phase measurement accuracy reaches 1 × 10−4 cycles/Hz1/2 above 6 mHz after differential clock noise correction using measured clock jitter.
Large-scale laser gyroscopes have found important applications in Earth sciences due to their self-sufficient property of measurement of the Earth’s rotation without any external references. In order to extend the relative rotation measurement accuracy to a better level so that it can be used for the determination of the Earth orientation parameters (EOP), we investigate the limitations in a passive resonant laser gyroscope (PRG) developed at Huazhong University of Science and Technology (HUST) to pave the way for future development. We identify the noise sources from the derived noise transfer function of the PRG. In the frequency range below , the contribution of free-spectral-range (FSR) variation is the dominant limitation, which comes from the drift of the ring cavity length. In the to frequency range, the limitation is due to the noises of the frequency discrimination system, which mainly comes from the residual amplitude modulation (RAM) in the frequency range below 2 Hz. In addition, the noise contributed by the Mach–Zehnder-type beam combiner is also noticeable in the 0.01 to 2 Hz frequency range. Finally, possible schemes for future improvement are also discussed.