A sodium chloride modification was applied where different amounts of sodium chloride was physically blended in a tin oxide colloid solution to passivate the interface between the electron transport layer (ETL) and perovskite layer and improve the performance of perovskite solar cells. Sodium chloride-modified tin oxide was utilized as the electron transport material to fabricate perovskite solar cells. It was found that sodium chloride-modified tin oxide as an ETL could considerably enhance the performance of the device compared to pristine tin oxide. The power conversion efficiency of the perovskite solar cell displayed 8.8% remarkable improvement from 18.7 ± 0.4% to 20.3 ± 0.3% on average and 9.5% improvement from 18.9 to 20.7% in champion devices because of the considerable enhancement of the fill factor when 25 mM sodium chloride-modified tin oxide as the ETL was used in comparison with pristine tin oxide.
In comparison to monolithic perovskite/perovskite double-junction solar cells, a four-terminal spectrum-splitting system is a simple method to obtain a higher power conversion efficiency (PCE) because it has no constraints of unifying the structures of the top and bottom cells. In this work, utilizing the fact that low-bandgap Sn-Pb bottom cells work the best in p-i-n while Pb-based wide-bandgap top cells work better in an n-i-p architecture, a wide-bandgap (Eg = 1.61 eV) perovskite solar cell with a mesoscopic structure and a narrow-bandgap (Eg = 1.27 eV) perovskite solar cell with an inverted structure were combined to fabricate a double-junction four-terminal spectral splitting solar cell. The double-junction solar cell with the 801 nm spectral splitting with an active area of 0.18 cm2 was found to work with a PCE of 25.3%, which is the highest reported so far for a 4-T all-perovskite double-junction spectral splitting solar cell.
Herein, quasi-two-dimensional (Q-2D) (PEA)(2)MA(4)Pb(5)I(16) (prepared by a two-step process) and hole transport layer of a solar cell were fabricated in a high relative humidity (25 +/- 5%) environment. The PSC behavior of most Q-2D perovskites is worse than that of three-dimensional perovskites owing to the horizontal alignment of the innate characteristic organic plates on the substrate. Using hybrid immersion solvents (HISs), we have improved vertical alignment in an appropriate ratio to enhance the efficiency of charge transfer and the high coverage of the first priming layer (first step). The grazing incidence X-ray diffraction pattern of the optimized structures revealed a preferential orientation for the vertical alignment of (111), which improved the charge transfer in PSCs and micrometer-level grain size growth. The second step was processed in a high-humidity environment (50 +/- 5%) (methylammonium iodide solution embedded), and Q-2D (PEA)(2)MA(4)Pb(5)I(16) demonstrated distinct grain boundaries. The power conversion efficiency (PCE, 13.09%) of the champion device of the first priming layer prepared using the HIS system increased by >55% compared to the single-immersion solvent (8.3%). The PCE of the ion-modified ETL PSCs was 16.02% (CsF-3) and 14.58% (CsCl-3) and demonstrated 22 and 11% improvement, respectively. The ion-modified electron transport layer (ETL) was deposited in the air, which reduced the power consumption of preparing perovskite solar cells (PSCs). Finally, all Q-2D PSCs were stored in the air, and three PSCs (DMF/DMSO, CsF-3, and CsCl-3) using HIS exhibited long-term stability for 1 month maintaining 80-88% of PCE, demonstrating the importance of the HIS system to improve the first step of growth orientation, which enhances the stability and photovoltaic properties of PSCs.
17 October 2023 in ACS Applied Electronic Materials
Photodetectors are widely applied in modern industrial fields because they convert light energy into electrical signals. We propose a printable silver (Ag) paste electrode for a highly flexible metal–semiconductor–metal (MSM) broadband visible light photodetector as a wearable and portable device. Single-crystal and surface-textured silicon substrates with thicknesses of 37.21 μm were fabricated using a wet etching process. Surface texturization on flexible Si substrates enhances the light-trapping effect and minimizes reflectance from the incident light, and the average reflectance is reduced by 16.3% with pyramid-like structures. In this study, semitransparent, conductive Ag paste electrodes were manufactured using a screen-printing with liquid-phase process to form a flexible MSM broadband visible light photodetector. The transmittance of the homemade Ag paste solution fell between 34.83% and 36.98% in the wavelength range of visible light, from 400 nm to 800 nm. The highest visible light photosensitivity was 1.75 × 104 at 19.5 W/m2. The photocurrents of the flexible MSM broadband visible light photodetector were slightly changed under concave and convex conditions, displaying stable and durable bending properties.
About Me
Ching-Chang Lin is a researcher at the Research Center for Advanced Science and Technology (RCAST), the University of Tokyo.
Ching-Chang Lin is a researcher at the Research Center for Advanced Science and Technology (RCAST), the University of Tokyo.