The article presents the research findings on the process of machining with a pulsating water jet. The study determined the influence of water velocity and pressure, providing insights into the dynamics of pulsating water jets. An evaluation of the generation process of pulsating water jets was conducted for various models of self-excited pulsating heads. The aim was to determine the impact of geometric parameters of the self-excited pulsating head and hydrodynamic working conditions on the performance of such a head, the dynamic characteristics of the water jet it produces, and its technological suitability for material erosion. In the first stage, simulation studies were carried out for three models of self-excited pulsating heads. Based on these studies, a solution with appropriate geometry was selected. Subsequently, experimental studies were conducted using the self-excited head and dedicated research setups. For the selected solution of the self-excited pulsating head, pulse durations, jet thrust forces, and frequency variations for different working pressure values were determined. The analysis showed a correlation between the geometric parameters of the head, pressure changes, and the characteristics of the generated pulses in the pulsed water jets. Pulse generation was made possible by increasing the water flow through side openings. Pulses with greater water volume exhibited increased erosive potential, particularly noticeable at higher pressures. It was found that pressure changes also affect the pulse frequency, with shorter intervals observed at lower pressures and longer intervals at higher pressures. The results presented in the paper highlight the importance of tool geometry and changes in water pressure at the inlet to the self-excited pulsating heads and the dynamics of the pulsed water jet. Research on the pulse generation mechanism and the assessment of erosive potential can form the basis for optimizing the design and operation of pulsating water jets in surface machining. This comprehensive understanding underpins the enhancement of efficiency and effectiveness of pulsating water jet applications in various industrial and manufacturing processes.
9 September 2023 in Archives of Civil and Mechanical Engineering
Water jet is an extensively used method for materials processing due to the possibility of operating in different environments (air, water), its safety during working with hazardous materials, and efficiency while cutting hard and brittle rock blocks. In this article, we have presented results of the research on processing aerated concrete by means of pulsating water jest. The discontinuity in water flow through the nozzle was achieved using an own-construction self-excited head. The intermittent flow had the greatest effect during operating in water environment. Machining efficiency for continuous and pulsating water jest was indicated by measuring erosive effects on processed materials. The occurrences of pulsations were confirmed while measurement of water jet thrust forces acting on piezoelectric sensor. It was concluded that pulsating water jet had greater processing effectiveness in a certain circumstances compared to the continuous flow, during the surface processing of concrete blocks.
A centrifugal disc and vibratory finishing machines were applied to improve the surface texture of soda-lime workpieces cut by an abrasive water jet. This innovative method was denoted as sequential smoothing treatment. An experimental study of the effect of the smoothing process conditions on the surface roughness, surface texture and micro roughness of the surface of glass workpieces was conducted. The analysis of the results obtained from experimental research made it possible to determine the optimum conditions for the smoothing process of glass workpieces after abrasive water jet cutting process. The proper selection of the finishing machine, machining media (abrasive chips) and compounds (liquids and powders) made it possible to reduce the surface roughness of areas located in the lower part of the cutting zone from Sa = 4.81 μm to Sa = 1.9 μm. The experimental results obtained confirmed the validity of using finishing machines to improve the surface quality of the soda-lime glass components. An important problem that requires further research is the increase in productivity and the reduction in machining time.
4 September 2024 in Archives of Civil and Mechanical Engineering
Surface texturing is a technique that allows for the shaping of surface topography to meet various mechanical and tribological requirements. Abrasive-water jet (AWJ) technology is a promising approach to surface texturing, offering minimal heat impact, flexibility, and compatibility with complex surface geometries. High-pressure abrasive-water jet (AWJ) technology, as an innovative and versatile approach, significantly expands the possibilities of surface texturing for materials. Its advantages, such as precision, minimal thermal impact, sustainability, and a wide range of industrial applications, make it an attractive solution across various sectors. With continuous development and integration with modern digital technologies, AWJ is becoming an increasingly practical and cutting-edge tool in surface processing. The abrasive-water jet texturing process also affects surface geometry during the mating of components, which may be significant in reducing wear. The aim of the research was to determine the feasibility of obtaining specific structures on the surface of 304/1.4301 steel using abrasive-water jet technology. Results show that the highest load-bearing ratio of Smrk1 peaks, approximately 25%, was achieved at a texturing speed of 0.803 m/min. Conversely, the lowest load-bearing ratio of Smrk1 peaks, below 10%, was achieved at a texturing speed of 1.948 m/min. Grinding the surface after texturing increases its load-bearing capacity, leading to a twofold increase in the ability to maintain an oil layer. The obtained results may find application in various fields where controlling surface geometry is essential for improving material functionality and efficiency.
The dynamic impact of a water jet with a periodically changing structure can be used in various industries. The paper presents a design solution for a self-excited pulse head. This head can be used in mining for drilling holes and breaking rocks. The design of the head was developed based on computer simulations, which made it possible to learn the mechanism of impulse shaping inside the head. Tests of the water jet produced in the self-excited pulsation head showed the occurrence of periodic changes in its internal structure and pulsation frequency. A significant increase in the dynamic stream pressures was demonstrated for the head working in the water environment compared to the head working in the air environment For example, for nominal medium and highest pressures, this increase is up to 82%, while for the lowest pressures (10 MPa), the pressure force values increase by 46%. It was found that an increase in the nominal water pressure causes a decrease in the frequency of hydrodynamic pulses in the head operating in both the water and air environment.
Electrical steels are widely used in the electrical industry in the construction of many devices, e.g., power transformer cores and distribution transformers. An important parameter of electrical components that determines the efficiency of devices is energy loss during remagnetization. These losses are influenced, among other factors, by steel cutting processes. The common techniques for cutting electrical materials on industrial lines are mechanical cutting and laser cutting. High-pressure abrasive water jet (AWJ) cutting, unlike the technologies mentioned above, can ensure higher quality of the cut edge and limit the negative impact of the cutting process on the magnetic properties of sheet metal. However, the correct control of the process and the conditions of its implementation comprise a complex issue and require extensive scientific research. This work presents a new approach to cutting electric sheets, involving bundle cutting, which significantly increases the processing efficiency and the dimensional and shape accuracy of the cut details. The tests were carried out for bundles composed of a maximum of 30 sheets, ready to be joined in a stator and rotor in a motor. The influence of processing conditions on the quality of the cut edges of sheet metal, the width of the deformation zone, and the burr height were analyzed. The detailed analysis of the quality of the cut edges of electrical bundled sheets creates new possibilities for controlling the AWJ cutting process in order to obtain a product with the desired functional and operational properties.