Czeslaw Łukianowicz

Prof. Czeslaw Łukianowicz

orcid

Research Focus & Metrics

Academic Career Length

50Years (1977-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
5 October 2022 in Materials
Verified
Journal Article
Open access
PDF file
MSMarzena Sutowska
Marzena Sutowska
CŁCzeslaw Łukianowicz
Czeslaw Łukianowicz
MSMonika Szada-Borzyszkowska
Monika Szada-Borzyszkowska
A centrifugal disc and vibratory finishing machines were applied to improve the surface texture of soda-lime workpieces cut by an abrasive water jet. This innovative method was denoted as sequential smoothing treatment. An experimental study of the effect of the smoothing process conditions on the surface roughness, surface texture and micro roughness of the surface of glass workpieces was conducted. The analysis of the results obtained from experimental research made it possible to determine the optimum conditions for the smoothing process of glass workpieces after abrasive water jet cutting process. The proper selection of the finishing machine, machining media (abrasive chips) and compounds (liquids and powders) made it possible to reduce the surface roughness of areas located in the lower part of the cutting zone from Sa = 4.81 μm to Sa = 1.9 μm. The experimental results obtained confirmed the validity of using finishing machines to improve the surface quality of the soda-lime glass components. An important problem that requires further research is the increase in productivity and the reduction in machining time.

1 March 2012 in Transactions of the Canadian Society for Mechanical Engineering
Verified
Journal Article
Closed access
Wojciech KapłonekWojciech Kapłonek
Wojciech Kapłonek
CŁCzeslaw Łukianowicz
Czeslaw Łukianowicz
KNKrzysztof Nadolny
Krzysztof Nadolny
Diagnostics of abrasive tools requires the use of modern measurement techniques which allows for fast assessment of a surface in order to determine, for example, the degree of its wear or to detect various type of defects. A wide group of optical measurement methods used for this type of assessment are based on the phenomenon of light scattering. One such method based on imaging and analysis of light scattering from a surface is laser scatterometry. In this paper, by utilizing laser scatterometry supported by image analysis techniques, a proposal for a methodology of assessment of the degree to which smearing of the grinding wheel active surface (GWAS) occurs during the plunge grinding process, was presented and discussed. Select results of experimental investigations carried out on bearing steel 100Cr6 were also presented. The obtained results confirmed the efficacy of the above-mentioned techniques that could be an interesting alternative to other methods already used in such measurements.

23 May 2012 in Materialwissenschaft und Werkstofftechnik
Verified
Journal Article
Closed access
PDF file
JVJan Valíček
Jan Valíček
Robert ČepRobert Čep
Robert Čep
Krzysztof RokoszKrzysztof Rokosz
Krzysztof Rokosz
CŁCzeslaw Łukianowicz
Czeslaw Łukianowicz
Drazan KozakDrazan Kozak
Drazan Kozak
BHB. Haluzíková
B. Haluzíková

24 August 2021 in Materials
Verified
Journal Article
Open access
PDF file
MRMarcin Romanowski
Marcin Romanowski
CŁCzeslaw Łukianowicz
Czeslaw Łukianowicz
MSMarzena Sutowska
Marzena Sutowska
WZWojciech Zawadka
Wojciech Zawadka
Danil PimenovDanil Pimenov
Danil Pimenov
KNKrzysztof Nadolny
Krzysztof Nadolny
Despite extensive knowledge of the cutting methods described, no universal method has been developed so far for evaluating the technological quality of elements shaped by different cutting processes. The aim of the research described in this article was to fill this gap and to propose the author’s methodology for the assessment of the technological quality of the surface of X5CRNI18-10 steel shaped as a result of laser cutting and abrasive water jet cutting. A synthetic index of technological quality assessment of the surface after cutting CTQ (cutting technological quality) was proposed. Three groups of factors were taken into account in the assessment of technological quality of the surface after cutting: selected surface texture parameters (arithmetic mean deviation of the surface Sa and total height of the surface St), results of measurements of dimensional accuracy of cut elements (length deviation LD and width deviation WD) as well as indicators of surface morphology estimated on the basis of microscopic images of the surface after cutting (deformation intensity DI and identification of cutting zones ICZ). On the basis of CTQ values determined, the cutting results of both cutting methods were compared. The analyses presented in this paper proved that the CTQ index can be effectively used to compare the results of a cutting process conducted using different methods and under different conditions. The developed CTQ index is a universal valuation tool, allowing for quantitative evaluation of features related to the technological quality of cutting process results.

1 December 1977 in Wear
Verified
Journal Article
Closed access
Tadeusz HryniewiczTadeusz Hryniewicz
Tadeusz Hryniewicz
TKTadeusz Karpinski
Tadeusz Karpinski
CŁCzeslaw Łukianowicz
Czeslaw Łukianowicz

13 August 2024 in Materials
Verified
Journal Article
Open access
PDF file
MRMagdalena Rzepka
Magdalena Rzepka
CŁCzeslaw Łukianowicz
Czeslaw Łukianowicz
WZWojciech Zawadka
Wojciech Zawadka
Krzysztof RokoszKrzysztof Rokosz
Krzysztof Rokosz
KNKrzysztof Nadolny
Krzysztof Nadolny
This article discusses a comparative analysis of the wear and quality of planer knife blades used in wood planers. The novelty in this work is the use of a simple coordinate measuring machine with a vision system to assess the wear of the cutting edges of planer knives. The primary objective of the research described in this paper was to verify whether the wear of the cutting edge of planer knives can be measured quickly and accurately using an optical coordinate measuring machine with a vision system. To date, contact profilometry methods have been used for this purpose, which require a specialist apparatus and qualified measuring equipment operators and are expensive and time-consuming. The research presented in this work was conducted on twelve planer knives. The condition and wear of the working surfaces of the tested knives were assessed using an optical digital microscope. The wear of the cutting edge of the knives was measured using two methods: the contact profilometry method and an optical coordinate measuring machine equipped with a vision system. The edge profiles and their parameters obtained by the optical method were compared to the results of measurements with a stylus profilometer. Based on the research and analyses conducted, it was found that the optical method used in this research significantly shortens the time of measuring the wear of the cutting edges of planer knives. In addition, this method has a wider measurement range, and the obtained measurement results are characterized by lower measurement uncertainty.