Over the past two decades, there has been a significant rise in the demand for Aluminum Metal Matrix Composites (AAMCs) due to their notable advantages such as lightweight properties, increased strength, and enhanced hardness. In this study, three distinct AAMC samples based on Al5083 alloy, each varying in reinforcement levels at 4%, 8%, and 12% by weight were used. These composites were produced through a stir-casting process. The biochar used in our research was obtained through a pyrolysis process, adding an environmentally friendly and sustainable aspect to the composite materials. In the machining aspect of the study, A systematic L27 Taguchi Design of Experiment approach was used to investigate the influence of input parameters, namely cutting speed, feed rate, depth of cut, and weight percentage of reinforcement material, on the machining process. Further regression models were developed to gain insights into the relationships between these parameters and the resulting surface roughness. Turning operations at a cutting speed of 1050 rpm, a feed rate of 60 mm, and a depth of cut of 0.75 mm were idle for superior surface roughness and to assess the impact of the reinforcement material on the machined surface.
18 September 2025 in Journal of Materials Engineering and Performance
Copper has good electrical and thermal conductivities and is used in numerous electrical and electronic applications as well as thermal management applications, but not for mechanical applications because of its low mechanical strength. In this research work, fabrication of graphene and graphene ferromolybdenum (Gr–FeMo) reinforced copper surface hybrid composites via Friction Stir Processing (FSP) technique is presented, which has high multifunctional properties. Optimum FSP conditions for surface reinforcement of commercially pure copper plates with graphene and graphene ferromolybdenum (1:1) hybrid mixture, respectively, at various volume fractions of 5, 15, and 25% have been performed. The surface hybrid composites thus fabricated have been characterized by SEM, energy-dispersive spectroscopy (EDS), Vickers microhardness, electrical and thermal conductivity. The microstructure analysis indicates that there is no defect formation in the composites due to severe plastic deformation caused by FSP technique. The highest microhardness (62.56 HV) was reached by the copper composite containing 5% of graphene, being 24% greater than the microhardness of untreated copper (50.60 HV), due to grain refinement, Orowan effect, and effective load transferring mechanism. The electrical conductivity of the hybrid composite 5% graphene–ferromolybdenum had the highest value of 1691.34 S/m while untreated copper had the value of 940.24 S/m. Thus, hybrid reinforcing had a positive impact on electron transport properties. Besides, the copper composite having 25% graphene had the highest thermal conductivity value equal to 1204.41 W m−1 K−1 compared to thermal conductivity of untreated copper (549.26 W m−1 K−1) due to good thermal conductivity properties of graphene. From the results received, it could be concluded that reinforcement with graphene and graphene–ferromolybdenum hybrid provides for a balanced reinforcement in terms of strength, electrical and thermal conductivity.
1 September 2025 in Materialwissenschaft und Werkstofftechnik
In this study, hybrid composites of Al7075 reinforced with boron carbide (B4C), titanium (Ti), and graphite (Gr) were synthesized using the stir casting technique and was investigated to assess their suitability for aerospace applications. Six different compositions were prepared by varying the vol% of B4C and Ti and maintaining a constant vol% of graphite in all composites. The physical and structural characteristics were analyzed through density measurements, porosity evaluation, and x-ray diffraction (XRD) analysis. The experimental and theoretical density values showed a decreasing trend with increased reinforcement, Porosity values were found to decrease with higher Ti content. XRD confirmed the presence of Al matrix phases along with B4C, Ti, and graphite, , indicating uniform distribution and phase stability. Corrosion resistance was assessed using static immersion tests, polarization studies, Nyquist plots, and Bode plots. The base alloy demonstrated susceptibility to galvanic corrosion, with minimal passivation. Composites with boron carbide showed moderate corrosion rate (−1.479 mm y−1), and those with titanium exhibited remarkable improvements (−1.116 mm y−1). The polarization curves of the reinforced composites displayed lower current densities in the anodic region with an Ecorr and Icorr value of 776.856 mV and 8.332 mA for composite reinforced with boron carbide and 727.265 mV and 8.001 mA for composites reinforced with titanium, indicating enhanced passivation and reduced corrosion rates. Nyquist plots revealed larger semicircular arcs for titanium-reinforced composites, signifying higher charge transfer resistance (Rct). Among the tested compositions, the hybrid composite with 7 vol% Ti, 3 vol% B4C, and 2 vol% Gr exhibited improved passivation, and superior corrosion resistance.