Julio Tinoco

Dr. Julio Tinoco

orcid

Research Focus & Metrics

Academic Career Length

22Years (2005-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
8 October 2018 in IEEE Electron Device Letters
Verified
Journal Article
Closed access
AMA. G. Martinez-Lopez
A. G. Martinez-Lopez
WPW. Y. Padron-Hernandez
W. Y. Padron-Hernandez
DPD. Pourjafari
D. Pourjafari
GOGerko Oskam
Gerko Oskam
GRGeonel Rodriguez-Gattorno
Geonel Rodriguez-Gattorno
JTJulio Tinoco
Julio Tinoco
TiO2 films have been used for novel sensor devices, thanks to their optical and chemical properties. The development of those applications often requires the features of rectifier devices. In this scenario, TiO2-based Schottky diodes become an interesting alternative. In this letter, a detailed electrical characterization of TiO2-based Schottky diodes is performed. Thin films of the three crystalline phases have been obtained by the inkjet printing technique at room temperature. Thermionic and Poole-Frenkel emission are identified as the main conduction mechanisms in these devices, and the barrier heights are reported for each crystal phase.

21 May 2022 in Micromachines
Verified
Journal Article
Open access
PDF file
JTJulio Tinoco
Julio Tinoco
SHSamuel A. Hernandez
Samuel A. Hernandez
M. De La L. OlveraM. De La L. Olvera
M. De La L. Olvera
MEMagali Estrada
Magali Estrada
RGRodolfo García
Rodolfo García
AMAndrea G. Martinez-Lopez
Andrea G. Martinez-Lopez
Schottky barrier diodes, developed by low-cost techniques and low temperature processes (LTP-SBD), have gained attention for different kinds of novel applications, including flexible electronic fabrication. This work analyzes the behavior of the I–V characteristic of solution processed, ZnO Schottky barrier diodes, fabricated at a low temperature. It is shown that the use of standard extraction methods to determine diode parameters in these devices produce significant dispersion of the ideality factor with values from 2.2 to 4.1, as well as a dependence on the diode area without physical meaning. The analysis of simulated I–V characteristic of LTP-SBD, and its comparison with experimental measurements, confirmed that it is necessary to consider the presence of a density of states (DOS) in the semiconductor gap, to understand specific changes observed in their performance, with respect to standard SBDs. These changes include increased values of Rs, as well as its dependence on bias, an important reduction of the diode current and small rectification values (RR). Additionally, it is shown that the standard extraction methodologies cannot be used to obtain diode parameters of LTP-SBD, as it is necessary to develop adequate parameter extraction methodologies for them.

5 September 2021 in Sensors
Verified
Journal Article
Open access
PDF file
AMAndrea G. Martinez-Lopez
Andrea G. Martinez-Lopez
DGDavid Guzman
David Guzman
IMIsrael Mejia
Israel Mejia
JTJulio Tinoco
Julio Tinoco
The development of silicon-based sensor devices has enabled the possibility to pursue novel integrated smart sensor technologies. Under this scenario, capacitive sensor devices are one viable option for implementing different kinds of applications. In this paper, an interdigitated coplanar capacitive device fabricated over a silicon substrate is presented and its potential use as liquid sensor is demonstrated. Additionally, a detailed capacitance model, which includes the parasitic capacitances introduced by the silicon substrate, was developed. The capacitance model has been theoretically validated through finite-element simulations as well as experimentally by comparison with fabricated devices. A polydimethylsiloxane mold has been fabricated and bonded to the sensor device with the aim of defining a cavity to collect the liquid sample into the device’s active region. The active capacitance component correlates to the electric field coupling between adjacent metal lines. Therefore, any change to the dielectric constant of the medium above the coplanar metal lines will produce a change to the device capacitance. Finally, the main guidelines for device performance improvement are depicted.

1 November 2025 in Physica Scripta
Verified
Journal Article
Closed access
JTJulio Tinoco
Julio Tinoco
RGRodolfo Garcia
Rodolfo Garcia
AMAndrea G. Martinez-Lopez
Andrea G. Martinez-Lopez
Schottky Barrier Diodes fabricated using nanostructured semiconductor materials have gained the attention of the community due to their potential novel applications as well as their use as circuit element. The electrical characterization of these kinds of devices usually gives ideality factor values greater than two and within a large dispersion. Different extraction methodologies have been developed based on the consideration that the diode parameters are constant. However, it has been found that the density-of-states into the semiconductor band gap produces a change of the semiconductor electron density as the applied voltage is increased, causing the presence of bias dependent series resistance, but its impact on the extraction procedures has not been properly addressed. Hence, numerical solution of the diode equation was performed with constant diode parameters and using bias dependent series resistance, three most used extraction methods were applied to analyse the possibility to properly estimate the diode parameters. It was found that extraction methods are no longer valid when diodes exhibit bias dependent parameters.

11 November 2019 in IEEE Transactions on Electron Devices
Verified
Journal Article
Closed access
YOANLYS HERNANDEZ BARRIOSYOANLYS HERNANDEZ BARRIOS
YOANLYS HERNANDEZ BARRIOS
ACAntonio Cerdeira
Antonio Cerdeira
JTJulio Tinoco
Julio Tinoco
BIB. Iniguez
B. Iniguez
In this article, we present the analysis of the nonlinear harmonic distortion (HD) characteristics for two kinds of amorphous oxide semiconductor thin film transistors (AOSTFTs) based on SiO₂/indium-gallium-zinc oxide (IGZO) and HfO₂/hafnium-indium-zinc oxide (HIZO), applying the integral function method (IFM). An analysis of the distortion of the transistors used as quasi-linear resistor and the variation in HD as a function of the parameter gm/IDS are also included. As far as we know, this kind of study has not been reported before. It is shown that parameter HD2 does not present a minimum as in MOSFETs, because the transfer characteristic does not present an inflection point. The value of HD2 is higher than that of HD3 in the whole operating ranges. When the transistor is used as quasi-linear resistor for different VG bias, HD2 is greater than HD3 in more than 50 dB. Because HD2 is significantly greater than HD3, the total HD (THD) parameter can be considered practically equal to HD2. In addition, the behavior of HD around the low-power operating region is shown.

1 November 2023 in Engineering Research Express
Verified
Journal Article
Closed access
PDF file
JTJulio Tinoco
Julio Tinoco
SHSamuel Hernandez
Samuel Hernandez
RGRodolfo Garcia
Rodolfo Garcia
RPRogelio de J. Portillo-Velez
Rogelio de J. Portillo-Velez
AMAndrea G. Martinez-Lopez
Andrea G. Martinez-Lopez
In the last years, the implementation of solution-processing techniques, as well as the use of nanostructured oxide semiconductors, have pursued the development of large-area electronic systems. However, the proper understanding of the electrical characteristics of this type of devices is needed with the aim to properly implement potential applications. In general, the diode behaviour at forward condition has been analysed in the literature, but at reverse condition further research is required. Therefore, in this work, the fabrication and electrical characterization at reverse condition of solution-processed Schottky-Barrier-Diodes based on ZnO-rods is presented. Two different conduction mechanisms with a transition occurring at around –2 V were observed. Also, numerical solutions of the diode reverse current characteristic, which includes the series resistance (R s ) for both conduction mechanisms, were implemented and the impact of the series resistance was addressed. Finally, a numerical optimization strategy was used to determine the diode parameters which best fit the experimental current.