Hong-liang LIU

Dr. Hong-liang LIU


Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
17 November 2022 in Materials
Verified
Journal Article
Open access
PDF file
HLHong-liang LIU
Hong-liang LIU
BYBo Yang
Bo Yang
YCYu Chen
Yu Chen
CLChuncheng Li
Chuncheng Li
Chengjun LiuChengjun Liu
Chengjun Liu
Based on theoretical calculations, laboratory simulation research and industrial production data analysis combined with characterisations such as metallographic microscope, scanning electron microscope (SEM), transmission electron microscope (TEM) and microhardness testing, this study investigated the state of occurrence and the precipitation law of vanadium (V) in microalloyed steel to determine a reasonable production process for V microalloyed steel. The results showed that the V(C,N) precipitation phase was the main form of V in microalloyed steel that precipitated after the transformation of austenite to ferrite. The amount of V precipitation was positively correlated with the amount of V that was added. However, the precipitation temperature was not significantly correlated with the amount added. When the V content increased from 0.03% to 0.06%, the initial precipitation temperature only increased by 23 °C. The coiling temperature was identified as the core factor affecting the strength of V microalloyed steel. When the effects of precipitation strengthening and microstructure strengthening were considered, as the coiling temperature decreased, the strength first increased, then decreased and finally increased again. Under different processing conditions, the strengthening of vanadium in the material increased first and then decreased as the temperature decreased (700–200 °C). The corresponding temperatures for the best strengthening effect of aging treatment, industrial statistical data and simulating coiling were 550, 470 and 400 °C, respectively. The difference between laboratory research results and industrial production was found. When V precipitation strengthening was used to improve material properties, it was necessary to determine a reasonable quantity of V to add and the production process, according to different alloy systems, to make more effective use of V microalloyed resources.

27 August 2023 in Metals
Verified
Journal Article
Open access
PDF file
YYYubo Yang
Yubo Yang
YFYu Fu
Yu Fu
GWGuangxin Wu
Guangxin Wu
HLHong-liang LIU
Hong-liang LIU
YCYu Chen
Yu Chen
QLQian Li
Qian Li
Liquid metal embrittlement (LME) in Zn-based coating plates during hot stamping is an abnormal phenomenon where intimate contact between liquid Zn and a steel matrix results in the penetration of liquid Zn into the matrix, causing ruptures. In order to alleviate LME phenomenon, this paper designed a series of eutectic Zn-Al-Mg coating alloys to improve the uniformity of the Zn element distribution in the coating during heat treatment and inhibit the reaction between Fe and Zn. The high temperature mechanical properties of the coated steels are determined using thermal simulation to calculate the relative reduction in fracture energy, which is used to evaluate the LME level of the different composition coatings. It is suggested that the Zn-4.5Al-3.0Mg coating shows the highest LME resistance at 920 °C. The microstructure of these Zn-Al-Mg coated steels is observed after austenitization at 850 °C~920 °C for 3 min, which shows that the uniformity of the microstructure after austenitizing is affected by the composition of the coating and the austenitizing temperature. The higher temperature benefits the homogenization of the coating and steel and inhibits LME. The findings of this study provide valuable insights for the development of ternary Zn based LME resistant coatings.

19 July 2022 in Metals
Verified
Journal Article
Open access
PDF file
HLHong-liang LIU
Hong-liang LIU
WDWenbin Du
Wenbin Du
HLHongzhou Lu
Hongzhou Lu
YFYujing Fu
Yujing Fu
SYShuai Yu
Shuai Yu
Chengjun LiuChengjun Liu
Chengjun Liu
This paper studies the effect of extreme cooling and traditional cooling on the microstructure of high-strength steel during hot rolling by adjusting the cooling process, combining the theoretical calculation and the thermal simulation experiment, and using metallographic microscope, scanning electron microscope (SEM), and electron backscattered diffraction (EBSD) analysis methods in order to solve the problem of coil collapse in the production process of high-strength steel. The research results show that compared with the traditional cooling method, the front-section fast cooling mode can rapidly cool the hot-rolled sheet to the “nose tip” temperature of the ferrite transformation of the time-temperature-phase-transition (TTT) curve, which can promote the transformation of the material to ferrite, increase the proportion of ferrite, and make the grain size of the organization finer. It helps to improve the overall mechanical properties of the material and reduce coil collapse defects. The front-section fast cooling mode achieves good results in industrial application, the proportion of coil collapse reduces from 9.363% to 0.533%, and the problem of coil collapse is significantly improved.

28 July 2023 in Metals
Verified
Journal Article
Open access
PDF file
JGJing Guo
Jing Guo
HLHong-liang LIU
Hong-liang LIU
XLXiaodong Li
Xiaodong Li
TYTianyi Yang
Tianyi Yang
Hot-stamped steel is currently the most widely used lightweight material in automobiles, and accurately predicting its failure risk during the simulation is a bottleneck problem in the automobile industry. In this study, the fracture failure behavior of the hot-stamped PHS2000 steel manufactured by Ben Gang Group (Benxi, China) is investigated by experiments and simulation. Static tension and high-speed tension tests are conducted to obtain the elastic-plastic stress-strain relations, and a Swift + Hockett–Sherby model is proposed to describe the hardening behavior under static and high-speed loads. Tests under five kinds of stress states, namely static shear, static tensile shear, notched static tension, center-hole static tension, and static punching, are conducted to obtain the ultimate fracture strains under different stress states for establishing a failure model. The finite element method (FEM) is used to inversely achieve the fracture parameters of the material, and the GISSMO model in LS-Dyna is adopted to describe the fracture characteristics of the material. A fracture card is further established for simulation analysis by combining fracture characteristics with high-speed tension curves and simultaneously loading size effect curves of meshes. Finally, the card is applied in the simulation of the three-point bending test. High-precision results of fracture simulation matching the experimental results are obtained. This research proves that the proposed fracture card is accurate and can be widely used in the simulation of fracture behaviors of the hot-stamped PHS2000 steel.

13 June 2024 in Materials Today Communications
Verified
Journal Article
Closed access
JGJing Guo
Jing Guo
LWLuning Wang
Luning Wang
TJTao Jiang
Tao Jiang
FWFei Wang
Fei Wang
HLHong-liang LIU
Hong-liang LIU
YCYing Chang
Ying Chang

26 February 2023
Verified
Book Chapter
Open access
PDF file
BYB. Yang
B. Yang
HLHong-liang LIU
Hong-liang LIU
TJT. Jing
T. Jing
YCY. Chen
Y. Chen
In this paper, the relationship between microstructure and mechanical properties of 22MnB5 hot stamping steel at different annealing temperatures was studied by optical microscope, scanning electron microscope and universal tensile test machine. The results showed that the tensile strength and yield strength decreased with the increasing of annealing temperature. When the pearlite was not spheroidized, the strength decline was due to the growth of grains caused by the diffusion of metal atoms during heating. When the pearlite was spheroidized, the solid solution atoms in the ferritic matrix of spheroidized pearlite were diffused and precipitated at grain boundaries. The solid solution atoms in the ferritic matrix were reduced and the effect of solid solution strengthening was reduced, which leads to the decreasing of the overall strength of the material.