Sergei Motorin

Mr. Sergei Motorin

orcid

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 March 2019 in Thermochimica Acta
Verified
Journal Article
Closed access
АKА.M. Kut'IN
А.M. Kut'IN
АPА.D. Plekhovich
А.D. Plekhovich
КBК.V. Balueva
К.V. Balueva
SMSergei Motorin
Sergei Motorin
VDVitaly V. Dorofeev
Vitaly V. Dorofeev

9 August 2021 in Photonics
Verified
Journal Article
Open access
PDF file
VDVitaly V. Dorofeev
Vitaly V. Dorofeev
VKVasily V. Koltashev
Vasily V. Koltashev
SMSergei Motorin
Sergei Motorin
APAlexander D. Plekhovich
Alexander D. Plekhovich
Arkady KimArkady Kim
Arkady Kim
A series of glass samples of the tungsten–tellurite system TeO2-WO3-Bi2O3-(4-x) La2O3-xEr2O3, x = 0; 0.4; 0.5; 0.7; 1.2; 2; 4 mol%, CEr = 0 - 15 × 1020 cm−3 were synthesized from high-purity oxides in an oxygen flow inside a specialized sealed reactor. In all samples of the series, an extremely low content of hydroxyl groups was achieved (~n × 1016 cm−3, more than 4 orders of magnitude lower than the concentration of erbium ions), which guarantees minimal effects on the luminescence properties of Er3+. The glasses are resistant to crystallization up to 4 mol% Er2O3, and the glass transition temperatures do not depend on the concentration of erbium oxide when introduced by replacing lanthanum oxide. Thin 0.2 mm plates have high transmittance at a level of 20% in the 4.7–5.3 µm range, and the absorption bands of hydroxyl groups at about 2.3, 3, and 4.4 µm, which are typical for ordinary tellurite glass samples, are indistinguishable. The introduction of erbium oxide led to an insignificant change in the refractive index. Er2O3-concentration dependences of the luminescence intensities and lifetimes near the wavelengths of 1.53 and 2.75 μm were found for the 4I13/2–4I15/2 and 4I11/2–4I13/2 /transitions of the Er3+ ion. The data obtained are necessary for the development of mid-infrared photonics; in particular, for the design of Er3+-doped fiber lasers.

1 February 2022 in Optics and Spectroscopy
Verified
Journal Article
Closed access
PDF file
ASArseny A. Sorokin
Arseny A. Sorokin
VDVitaly V. Dorofeev
Vitaly V. Dorofeev
SMSergei Motorin
Sergei Motorin
ILI. Lyashuk
I. Lyashuk
Jurģis PoriņšJurģis Poriņš
Jurģis Poriņš
VBVjaceslavs Bobrovs
Vjaceslavs Bobrovs
An optical fiber with a high Kerr nonlinearity coefficient has been proposed and manufactured from bismuth-modified tellurite glass for creation of non-classical multiphoton states of light. Specifically, we have proposed to use these fibers to squeeze the quantum fluctuations of one of the quadratures of light in the 20 W signal significantly below –10 dB compared to the standard quantum noise limit, which is important for various practical applications. Using numerical simulation based on the stochastic nonlinear Schrödinger equation, we have demonstrated noise squeezing stronger than –16 dB at tellurite fiber lengths of 6–14 m, while in squeezing of –14 dB is expected in silica glass fibers having lengths of 120–300 m. Analytical formulas were used to analyze the physical factors that limit the achievable squeezing.

9 December 2024 in Photonics
Verified
Journal Article
Open access
PDF file
SMSergei Muraviev
Sergei Muraviev
VDVitaly V. Dorofeev
Vitaly V. Dorofeev
SMSergei Motorin
Sergei Motorin
MKMaksim Jurievich Koptev
Maksim Jurievich Koptev
Arkady KimArkady Kim
Arkady Kim
The purpose of this paper was to develop fiber lasers in the 2.7–2.8 μm range based on the tungsten–tellurite glass fiber that is technically robust compared to the other fibers currently used in laser engineering. Using an advanced technology for producing ultra-dry tellurite glasses, we manufactured Er3+-doped tungsten–tellurite glass preforms with extremely low absorption and obtained active single-mode tungsten–tellurite fibers. Based on a 70 cm long fiber, we developed a laser oscillator pumped by a low-cost, high-efficiency diode laser at 976 nm. At the highest used pump power, the laser output reached 33 mW, which may be interesting for practical applications. We also measured the single-pass on/off gain of the fibers and showed that with increasing pump power amplification, as high as 5 can be reached, showing that such active fibers may also be used for increasing laser output.