An experimental product study of the reactions of furfural with the main tropospheric oxidants (Cl, OH and NO₃) has been carried out using a Fourier Transform Infrared spectrophotometer (FTIR) and a gas chromatograph–mass spectrometer with a time of flight detector (GC–TOFMS). The main gas-phase products detected were 5-chloro-2(5H)-furanone, maleic anhydride, 2-nitrofuran and CO. Molar yields were quantified for the detected products in these reactions, thus suggesting the existence of nongaseous products that could not be observed with the analytical techniques employed. The formation of Secondary Organic Aerosol (SOA) from the oxidation of furfural with Cl atoms, OH, NO₃ and ozone was investigated in a smog chamber in the absence of inorganic seed aerosols. The experimental results show the formation of ultrafine particles (less than 1 µm in diameter) for all of the studied reactions except for the nitrate radical. Given their small size, these ultrafine particles (<1 µm) can easily penetrate into the respiratory tract and reach the alveolar region. These particles, therefore, have the potential to cause severe damage to the respiratory system. The aerosol yield obtained, Y, was low (<0.04) in all cases, which means that the aerosols generated from furfural, under atmospheric conditions, could have little impact.

Data on the potential impact on human health of engineered nanomaterials are still scarce, with an evident lack of knowledge on the exposure levels at all stages of the life cycle. By prioritizing the responsible handling of engineered nanomaterials (ENMs), companies can promote sustainability by minimizing the risks of occupational exposure, protecting employee well-being, reducing liability, and avoiding costly environmental remediation efforts. This research aims to evaluate the risk in real scenarios involving the use of carbon-based nanomaterials in research laboratories, pilot-scale facilities, and industrial settings. Several online and offline instruments have been employed to characterize the particulate matter present in these environments, including particles in the nanometer range and relevant fractions for risk assessment purposes. Samples collected on polycarbonate filters were analyzed by scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDX). Exposure estimation has been performed by applying a decision based on tier 2 from the nanoGEM methodology, with the weighing and transferring of reduced graphene oxide (RGO) in a pilot plant being the most liberating processes, which are the activities with the highest risk of exposure. In addition, high levels of particle concentration, with peaks up to 1.7 × 10⁵ and 4.7 × 10⁵ part/cm³, have been found for the dispersion of carbon nanotubes (CNTs) and incorporation of carbonaceous nanoparticles into resins, respectively.

The use, production, and disposal of engineering nanomaterials (ENMs), including graphene-related materials (GRMs), raise concerns and questions about possible adverse effects on human health and the environment, considering the lack of harmonized toxicological data on ENMs and the ability of these materials to be released into the air, soil, or water during common industrial processes and/or accidental events. Within this context, the potential release of graphene particles, their agglomerates, and aggregates (NOAA) as a result of sanding of a battery of graphene-based polyester resin composite samples intended to be used in a building was examined. The analyzed samples were exposed to different weathering conditions to evaluate the influence of the weathering process on the morphology and size distribution of the particles released. Sanding studies were conducted in a tailored designed sanding bench connected to time and size resolving measurement devices. Particle size distributions and particle number concentration were assessed using an optical particle counter (OPC) and a condensation particle counter (CPC), respectively, during the sanding operation. A scanning electron microscope/energy dispersive X-ray (SEM/EDX) analysis was performed to adequately characterize the morphology, size, and chemical composition of the released particles. A toxicity screening study of pristine and graphene-based nanocomposites released using the aquatic macroinvertebrate Daphnia magna and relevant human cell lines was conducted to support risk assessment and decision making. The results show a significant release of nanoscale materials during machining operations, including differences attributed to the % of graphene and weathering conditions. The cell line tests demonstrated a higher effect in the human colon carcinoma cell line Caco2 than in the human fibroblasts (A549 cell line), which means that composites released to the environment could have an impact on human health and biota.