The main objective of this study was to measure and determine the efficiency of poly-crystalline, mono-crystalline and amorphous silicon solar module by applying single-axis time/date solar tracker to the installation of photovoltaic panel (dynamic system) as a strategy to increase the performance of the modules under hot-humid climate of Malaysia. The dynamic system in this experiment was designed to support the three types of PV panels which allowed it to move with single degree of freedom (horizontally) according to the sun’s orientation (sunrise to sunset) from east to west. Studies on sun movement in equator countries have been conducted to locate the sun‘s position on site (azimuth and altitude angle) using the Stereographic Diagram and Tabulate Daily Solar Data. It was found that poly-crystalline solar module have shown better performance ratio and average module efficiency compare to the others tested PV module under Malaysian climate.
Fossil fuel consumption for electricity generation in the building sector is at an all-time high in line with the country’s economic growth. This scenario will increase the global CO2 emissions and large carbon footprints, thus leading to global warming. In recent years, most of the research related to the building sector has focused on the development of new techniques to reduce buildings’ energy consumption through energy conservation, energy efficiency, and the implementation of renewable energy technologies. The introduction of photovoltaic (PV) technology has become the most prominent renewable energy (RE) that can be integrated into building components. Even though the Building Integrated Photovoltaic (BIPV) has been available for decades, but its implementation in Southeast Asian countries has not gained widespread acceptance compared to European countries and other parts of Asia. This paper aims to investigate the effects and challenges of BIPV implementation in Southeast Asian Countries (Cambodia, Indonesia, Laos, Malaysia, Singapore, Thailand, Vietnam, and the Philippines), focusing on climate effects, the initial cost of PV technology, government policies, and initiatives. An in-depth literature review from past research, policies, and reports taken between 2016 to 2021 has been conducted and found that the environmental parameters directly influence the performance of BIPV systems and affect efficiency. This study pointed at Feed-in Tariff (FiT), policies and initiatives offered by the government in Southeast Asian countries are not beneficial and discourage building owners to adopt the BIPV technology or any other RE technology. Governments should revise the current policies to promote and attract more building owners to take part in the efforts to minimize CO2 emissions from the building industry.
Building sector is associated with high energy consumption and greenhouse gas emissions, which contribute to climate change. Sustainable development emphasizes any actions to reduce climate change and its effect. In Malaysia, half of the energy utilized in buildings goes towards building cooling. Thermal comfort studies and adaptive thermal comfort models reflect the high comfort temperatures for Malaysians in naturally conditioned buildings, which make it possible to tackle the difference between buildings’ indoor temperature and the required comfort temperature by using proper passive measures. This study investigates the effectiveness of building’s retrofitting with phase change materials (PCMs) as a passive cooling technology to improve the indoor thermal environment for more comfortable conditions. PCM sheets were numerically investigated below the internal finishing of the walls. The investigation involved an optimization study for the PCMs transition temperatures and quantities. The results showed significant improvement in the indoor thermal environment, especially when using lower transition temperatures and higher quantities of PCMs. Therefore, the monthly thermal discomfort time has decreased completely, while the thermal comfort time has increased to as high as 98%. The PCM was effective year-round and the optimum performance for the investigated conditions was achieved when using 18mm layer of PCM27-26.
23 February 2017 in International Journal of Low-Carbon Technologies
Photovoltaic (PV) façade, an envelope of the building in an urban area, can potentially produce clean electricity to meet the energy demand of the buildings and also provides protection from weather. This paper focuses on the application of PV technology on vertical façade of the building which is considered as an element of building-integrated PV. The aim of this study is to assess the feasibility with regard to performance evaluation of PV vertical façade based on the built-up model of a high-rise building in Malaysia using system advisor model. The best four vertical façade orientations for PV application in climatic condition of Malaysia are east, west, southeast and southwest as these façades received the highest incident irradiance. Based on the typical high-rise office building in Malaysia, the energy generated through the vertical PV system is between 400 and 700 MWh, whereas the energy generated by the roof system is ~240 MWh annually.
2 October 2023 in Journal of Advanced Research in Applied Sciences and Engineering Technology
This article explores the impact of adjacent buildings on solar exposure for photovoltaic (PV) applications in high-rise urban areas in Malaysia. The rapid urbanization and population density in Malaysia's high-rise areas have increased energy demand, necessitating the exploration of alternative energy sources. Integrating PV systems into vertical façades offers a promising solution for maximizing energy generation in space-constrained urban environments. However, the efficacy of PV systems is influenced by adjacent buildings, including their arrangement, height, and orientation, which affect solar exposure and energy generation potential. Understanding these effects is crucial for optimizing PV system design and placement. This study aims to investigate the relationship between adjacent buildings and solar exposure for PV panels mounted on high-rise buildings in Malaysia. By examining these effects, the research provides valuable insights for urban planners, architects, and renewable energy practitioners involved in sustainable urban development. The findings will inform decisions regarding the integration of PV systems, promoting renewable energy adoption, and reducing the environmental impact of urban areas. The article also discusses Malaysia's climate, energy consumption, and solar radiation potential, emphasizing the need to harness solar energy in a country blessed with abundant sunlight. The challenges faced by current air conditioning systems and building-integrated photovoltaic (BIPV) applications in Malaysia are outlined, along with efforts to address them through energy-efficient systems and awareness campaigns. The research conducted simulations using a 3D model in Kuala Lumpur, Malaysia, considering different heights and distances of adjacent buildings. The software used for simulations was IES-VE, which offers various modules for energy consumption analysis. The results demonstrate how adjacent buildings affect the annual average energy for different scenarios, highlighting the importance of distance and height. The findings provide insights into the monthly average energy variations and emphasize the relationship between adjacent building height and average energy levels. Overall, this research contributes to the efficient utilization of vertical façades for harnessing solar energy in high-rise urban areas, supporting Malaysia's sustainable energy goals while ensuring urban environment liveability and resilience.