Lijie Ma

Lijie Ma


Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
21 June 2022 in Micromachines
Verified
Journal Article
Open access
PDF file
ZWzhankui Wang
zhankui Wang
ZZZhao Zhang
Zhao Zhang
SWShiwei Wang
Shiwei Wang
MPMinghua Pang
Minghua Pang
LMLijie Ma
Lijie Ma
JSJianxiu Su
Jianxiu Su
The surface condition of the fixed abrasive pad (FAP) has a significant impact on its machining performance, workpiece material removal rate (MRR), and surface roughness. To clarify the wavelet packet energy characteristics of friction signal under different surface conditions of FAP and its mapping relationship with MRR and workpiece surface quality, FAP samples in different processing stages were obtained through a consolidated abrasive grinding quartz glass experiment. Then, the friction signals in different stages were received by the friction and wear experiment between the FAP and quartz glass workpiece, and the wavelet packet analysis was carried out. The experimental results show that with the increase of lapping time, the surface wear degree of the FAP increased gradually, and the MRR of the workpiece, the surface roughness of the FAP, and the surface roughness of the workpiece decreased slowly. In the wavelet packet energy of friction signal during machining, the energy proportion of frequency band 7 showed an upward trend with the increase of lapping time. The energy proportion of frequency band 8 showed a downward trend with the increase of lapping time. The change characteristics of the two are significantly correlated with the surface condition of the FAP.

29 July 2022 in Materials
Verified
Journal Article
Open access
PDF file
ZWzhankui Wang
zhankui Wang
SWShiwei Wang
Shiwei Wang
YDYangyang Ding
Yangyang Ding
YYYakun Yang
Yakun Yang
LMLijie Ma
Lijie Ma
JSJianxiu Su
Jianxiu Su
Clarifying the influence of the dress process parameters of the abrasive water jet on the dressing effect of fixed-abrasive pads (FAPs) is a prerequisite for online controllable dressing of abrasive water jets. This paper uses three factors and three horizontal response surface methods to explore the influence of jet pressure, abrasive concentration, and nozzle angle on FAP dressing quality. The prediction model of the material removal rate of a FAP machined using three process parameters is established. The influence of pairwise interactions of the three process parameter variables on the dressing effect and the optimal process parameters under each target is analyzed. Finally, the optimal process parameters predicted by the model are verified by experiments. The results show that the best dressing parameters with the MRR of the workpiece as the response value are as follows: jet pressure 3.8 MPa, abrasive concentration 3%, and nozzle angle 73°. The predicted value of the optimal process performance is 464.574 nm/min, and the experimental verification result is 469.136 nm/min; the error between the experimental value and the predicted value is within a reasonable range.

23 August 2024 in Journal of Materials Engineering and Performance
Verified
Journal Article
Closed access
PDF file
LMLijie Ma
Lijie Ma
ZLZengrong Liu
Zengrong Liu
CFCuiya Feng
Cuiya Feng
BZBin Zhang
Bin Zhang
MPMinghua Pang
Minghua Pang
YWYongkui Wang
Yongkui Wang

24 November 2025 in Nanoscale
Verified
Journal Article
Closed access
PDF file
CYChenglong Yang
Chenglong Yang
KYKang Yang
Kang Yang
YYYuliang Yin
Yuliang Yin
FGFei Gao
Fei Gao
LLLeyang Li
Leyang Li
ZWZheng Jun Wang
Zheng Jun Wang
Nanomaterials have garnered significant attention due to their exceptional tribological properties.

26 June 2025 in Granular Matter
Verified
Journal Article
Closed access
PDF file
QFQigao Feng
Qigao Feng
GHGuiling Hu
Guiling Hu
ZGZichen Gan
Zichen Gan
LMLijie Ma
Lijie Ma
MPMinghua Pang
Minghua Pang
LLLeyang Li
Leyang Li