Jianxiu Su

Prof. Jianxiu Su

Henan Institute of science and technology
orcid

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
12 December 2021 in Micromachines
Verified
Journal Article
Open access
PDF file
WQWanting Qi
Wanting Qi
XCXiaojun Cao
Xiaojun Cao
WXWen Xiao
Wen Xiao
ZWzhankui Wang
zhankui Wang
JSJianxiu Su
Jianxiu Su
Na2CO3—1.5 H2O2, KClO3, KMnO4, KIO3, and NaOH were selected for dry polishing tests with a 6H-SiC single crystal substrate on a polyurethane polishing pad. The research results showed that all the solid-phase oxidants, except NaOH, could decompose to produce oxygen under the frictional action. After polishing with the five solid-phase oxidants, oxygen was found on the surface of SiC, indicating that all five solid-phase oxidants can have complex tribochemical reactions with SiC. Their reaction products are mainly SiO2 and (SiO2)x. Under the action of friction, due to the high flash point temperature of the polishing interface, the oxygen generated by the decomposition of the solid-phase oxidant could oxidize the surface of SiC and generate a SiO2 oxide layer on the surface of SiC. On the other hand, SiC reacted with H2O and generated a SiO2 oxide layer on the surface of SiC. After polishing with NaOH, the SiO2 oxide layer and soluble Na2SiO3 could be generated on the SiC surface; therefore, the surface material removal rate (MRR) was the highest, and the surface roughness was the largest, after polishing. The lowest MRR was achieved after the dry polishing of SiC with KClO3.

20 May 2023 in The International Journal of Advanced Manufacturing Technology
Verified
Journal Article
Closed access
PDF file
MXMingpu Xue
Mingpu Xue
WXWen Xiao
Wen Xiao
TZTianyi Zhang
Tianyi Zhang
ZWzhankui Wang
zhankui Wang
JSJianxiu Su
Jianxiu Su

21 June 2022 in Micromachines
Verified
Journal Article
Open access
PDF file
ZWzhankui Wang
zhankui Wang
ZZZhao Zhang
Zhao Zhang
SWShiwei Wang
Shiwei Wang
MPMinghua Pang
Minghua Pang
LMLijie Ma
Lijie Ma
JSJianxiu Su
Jianxiu Su
The surface condition of the fixed abrasive pad (FAP) has a significant impact on its machining performance, workpiece material removal rate (MRR), and surface roughness. To clarify the wavelet packet energy characteristics of friction signal under different surface conditions of FAP and its mapping relationship with MRR and workpiece surface quality, FAP samples in different processing stages were obtained through a consolidated abrasive grinding quartz glass experiment. Then, the friction signals in different stages were received by the friction and wear experiment between the FAP and quartz glass workpiece, and the wavelet packet analysis was carried out. The experimental results show that with the increase of lapping time, the surface wear degree of the FAP increased gradually, and the MRR of the workpiece, the surface roughness of the FAP, and the surface roughness of the workpiece decreased slowly. In the wavelet packet energy of friction signal during machining, the energy proportion of frequency band 7 showed an upward trend with the increase of lapping time. The energy proportion of frequency band 8 showed a downward trend with the increase of lapping time. The change characteristics of the two are significantly correlated with the surface condition of the FAP.

29 July 2022 in Materials
Verified
Journal Article
Open access
PDF file
ZWzhankui Wang
zhankui Wang
SWShiwei Wang
Shiwei Wang
YDYangyang Ding
Yangyang Ding
YYYakun Yang
Yakun Yang
LMLijie Ma
Lijie Ma
JSJianxiu Su
Jianxiu Su
Clarifying the influence of the dress process parameters of the abrasive water jet on the dressing effect of fixed-abrasive pads (FAPs) is a prerequisite for online controllable dressing of abrasive water jets. This paper uses three factors and three horizontal response surface methods to explore the influence of jet pressure, abrasive concentration, and nozzle angle on FAP dressing quality. The prediction model of the material removal rate of a FAP machined using three process parameters is established. The influence of pairwise interactions of the three process parameter variables on the dressing effect and the optimal process parameters under each target is analyzed. Finally, the optimal process parameters predicted by the model are verified by experiments. The results show that the best dressing parameters with the MRR of the workpiece as the response value are as follows: jet pressure 3.8 MPa, abrasive concentration 3%, and nozzle angle 73°. The predicted value of the optimal process performance is 464.574 nm/min, and the experimental verification result is 469.136 nm/min; the error between the experimental value and the predicted value is within a reasonable range.

21 April 2023 in Micromachines
Verified
Journal Article
Open access
PDF file
YZYanling Zheng
Yanling Zheng
ZZZhao Zhang
Zhao Zhang
ZWzhankui Wang
zhankui Wang
MPMinghua Pang
Minghua Pang
LMLijie Ma
Lijie Ma
JSJianxiu Su
Jianxiu Su
Abrasive water jetting is an effective dressing method for a fixed abrasive pad (FAP) and can improve FAP machining efficiency and the impact of abrasive water jet (AWJ) pressure on the dressing effect; moreover, the machining state of FAP after dressing has not been thoroughly studied. Therefore, in this study, the FAP was dressed by using AWJ under four pressures, and the dressed FAP was subjected to lapping experiments and tribological experiments. Through an analysis of the material removal rate, FAP surface topography, friction coefficient, and friction characteristic signal, the influence of AWJ pressure on the friction characteristic signal in FAP processing was studied. The outcomes show that the impact of the dressing on FAP rises and then falls as the AWJ pressure increases. The best dressing effect was observed when the AWJ pressure was 4 MPa. In addition, the maximum value of the marginal spectrum initially rises and then falls as the AWJ pressure increases. When the AWJ pressure was 4 MPa, the peak value of the marginal spectrum of the FAP that was dressed during processing was the largest.

30 October 2022 in Machines
Verified
Journal Article
Open access
PDF file
JYJianguo Yao
Jianguo Yao
HLHaixu Liu
Haixu Liu
ZWzhankui Wang
zhankui Wang
YZYongwei Zhu
Yongwei Zhu
JSJianxiu Su
Jianxiu Su
Chemical mechanical polishing (CMP) technology is one of the key technologies to realize the global planarization of semiconductor wafer surfaces. With the increasing popularity and universality of its application, more and higher requirements are put forward for ultra-precision machining. As an important part of the CMP system, polishing pads occupy a dominant position. In this paper, a self-regressive fixed abrasive polishing pad (SR-FAPP) was prepared by photo-curing. The physical and mechanical properties of the SR-FAPP and the retreat threshold of the abrasive particles on the SR-FAPP were studied. After the CMP of the SiC wafer with a polyurethane polishing pad and the SR-FAPP, it was found that the material removal rate of the former was 75% higher than that of the latter, and the surface roughness of the latter was 75% higher than that of the former. In the micro-morphology, the scratches on the surface of the latter’s polished SiC wafer were obviously reduced, which effectively improved the unevenness of the scratches on the surface of the SiC wafer after polishing, thus providing a reference for the preparation and performance research of the polishing pad.