Grzegorz Kosobudzki

Dr. Grzegorz Kosobudzki

orcid

Research Focus & Metrics

Academic Career Length

18Years (2009-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
5 June 2009 in IEEE Transactions on Applied Superconductivity
Verified
Journal Article
Closed access
ASA. Stafiniak
A. Stafiniak
GKGrzegorz Kosobudzki
Grzegorz Kosobudzki
A significant cryogenic load is generated in rapidly-cycling superconducting magnets due to ac losses. This load should not be excessive, otherwise cryogenic system will not be able to evacuate heat and magnet will quench. To verify magnet design and to know real cryogenic load the test of ac losses has to be performed. Electrical and calorimetric methods can be used for this purpose. The calorimetric method is slower because it requires stabilization of cryogenic system. The electrical method called V-I is faster and it can be applied to any magnet independent of its cooling schemes. With this method ac losses are measured directly and results are provided on-line. However, the electrical method is considered more error prone, mainly due to the fact that power factor of superconducting magnets is close to zero.


1 November 2018
Verified
Conference Paper
Closed access
DDDaniel Dusza
Daniel Dusza
GKGrzegorz Kosobudzki
Grzegorz Kosobudzki
The paper shows that a generalized unique definition of additive reactive power derives from the general definition of active power. Unlike active power, reactive power must be independent of the conversion of electric energy into work and heat. This independence is achieved if one of the waveforms - the current in the scalar voltage and current product (specifying active power) - is replaced by a special orthogonal waveform (a current derivative). Some properties of reactive power defined in this way are presented. Based on the theory proposed by Illiovici, a measurement stand was designed and built to allow measurement verification of theory and simulation tests.

20 May 2025 in Energies
Verified
Journal Article
Open access
PDF file
GKGrzegorz Kosobudzki
Grzegorz Kosobudzki
DDDaniel Dusza
Daniel Dusza
MCMarek Pawel Ciurys
Marek Pawel Ciurys
ALAleksander Leicht
Aleksander Leicht
The paper investigates an alternative approach to measuring and compensating reactive power in electric machines, particularly under non-sinusoidal voltage and current waveforms. Traditional power definitions, such as those introduced by Budeanu and Fryze, as well as the power triangle, are discussed alongside integral definitions of reactive power, which account for waveform distortions. This approach is novel and has not been previously applied in the context of electric machines. A digital algorithm for reactive power calculation, based on the integral definition, is proposed. It requires minimal computational resources and is easy to implement. Experimental measurements conducted on a single-phase induction motor demonstrate the impact of capacitive compensation on current waveforms. The results confirm the validity of the adopted definition of reactive power. With full reactive power compensation, the RMS value of the current drawn by the motor is minimized, which is not always the case with the classical approach to improving the power factor. The findings highlight the importance of accurate reactive power measurement and compensation in enhancing the performance and energy efficiency of electrical machines. The proposed approach is applicable not only to single-phase motors but also more broadly in determining the reactive power drawn by electric machines and in measuring electric energy, particularly in the presence of distorted voltages and currents.

1 November 2018
Verified
Conference Paper
Closed access
GKGrzegorz Kosobudzki
Grzegorz Kosobudzki
MRMyhajlo Rogoza
Myhajlo Rogoza
OLOleksandra Lysenko
Oleksandra Lysenko
YPYurii Papaika
Yurii Papaika
Dependences of the level of receiving circuit current pulsation of a contactless electric locomotive while using direct current pulse-width converter in the circuit to control traction drive upon the parameters of π-shaped filter components and commutation frequency of a converter have been obtained basing upon the use of topological method of directed graphs. The proposed method has made it possible to calculate filter parameters and give certain recommendations as for the converter commutation frequency according to the condition of providing minimum level of current pulsation of the electric locomotive receiving circuit.

23 December 2025 in PRZEGLĄD ELEKTROTECHNICZNY
Verified
Journal Article
Closed access
MSMonika Szafrańska
Monika Szafrańska
GKGrzegorz Kosobudzki
Grzegorz Kosobudzki
ZJZbigniew Jóskiewicz
Zbigniew Jóskiewicz
Niniejszy artykuł analizuje obecne wymagania dotyczące liczników energii elektrycznej, ze szczególnym uwzględnieniem testów odporności elektromagnetycznej (EMC). Wskazuje na braki w obowiązujących standardach, które nie obejmują wszystkich typów zakłóceń elektromagnetycznych występujących w rzeczywistym środowisku pracy liczników. Autorzy proponują włączenie dodatkowych procedur testowych, które obecnie nie są wymagane dla liczników. W artykule wskazano konieczność przejścia z tradycyjnego podejścia na rzecz analizy ryzyka uwzględniającej potencjalne konsekwencje nieprawidłowego działania licznika.