In this study, the interactions of magnesium (Mg) atom and Mg(001) surface with different metal-atom-doped graphene were investigated using a density functional theory (DFT) method. For the interactions of magnesium with Al-, Mn-, Zn-, and Zr-doped and intrinsic graphene, it was found that the magnesium atoms were physisorbed into the hollow sites of the intrinsic graphene with only the smallest interaction energy (approximately −1.900 eV). However, the magnesium atoms tended to be chemisorbed on the doped graphene, which exhibited larger interaction energies and charge transfers. Additionally, the Zn-doped graphene displayed the largest interaction energy with the Mg atom (approximately −3.833 eV). For the interactions of Mg(001) with Al-, Mn-, Zn-, and Zr-doped and intrinsic graphene (intrinsic and doped graphene/Mg interface), doped atoms interacted with a Mg layer to make graphene wrinkle, resulting in a higher specific surface area and better stability. Mg–C chemical bonds were formed at the Al-, Zn-, and Zr-doped interface, and Mg–Mn chemical bonds were formed at the Mn-doped interface. This study provided the fundamental research for future research into doped atoms on graphene reinforced magnesium matrix composites.
The high uniform magnetic field combined with pre-deformation and vacuum heat treatment processing is designed for improving the diffusion bonding properties of the 1420 Al-Li alloy. Serial magneto-thermal coupling treatment experiments of 1420 Al-Li alloy and the pure aluminium diffusion couple, together with the gallium interlayer, is carried out in a superconducting high magnetic field device. Various parameter combinations are used to produce different samples on which interface organization and connection performance are studied. Electron microscopic analysis reveals various interface topographies and fracture morphologies after shear strength tests. Influence of diffusion bonding temperature on element diffusion under a high uniform magnetic field is investigated. The diffusion activation energy of Mg element in pure aluminum under a 12 T magnetic field is calculated in this paper. It is found that the bonding quality and bonding performance of the interface are improved greatly after heat treatment with a strong magnetic field, and the bonding temperature is an important factor affecting the interface bonding and bonding strength. The diffusion coefficient of the Mg element in the 1420 Al-Li alloy to L2 pure aluminum increases with the increase of diffusion bonding temperature. Reducing the activation energy of elemental diffusion is beneficial to atomic diffusion.
The two-sheet hollow structure of the 1420 Al-Li alloy was prepared by the method of superplastic forming and diffusion bonding. The interface combination status of the diffusion bonding region and the microstructure of the superplastic forming region were observed by an optical microscope. The thickness distribution of the superplastic forming region was measured by an ultrasonic thickness meter machine, the defect detection was tested by X-ray nondestructive inspection, and the failure modes of the samples were analyzed. The results showed that the two-sheet hollow structure of the 1420 Al-Li alloy was prepared successfully, the structure was integrated, and there were no shape defects such as pit, wrinkle, and collapse. The structure shape was almost attached to the die completely, and the thickness was almost uniform distribution. The no deforming area of the two-sheet hollow structure of the 1420 Al-Li alloy was a long strip, rolled microstructure, while the grains near the round corner area were equiaxed states resulting from dynamic recrystallization. The improper control of the superplastic gas pressure in the forming process would lead to the tearing or the die-attaching failure for the two-sheet hollow structure of the 1420 Al-Li alloy.
Based on molecular dynamics simulation, this work investigated the influences of temperature and Ti volume fractions on the compressive deformation of Ti/Al layered composites. According to the simulation, the initial dislocations during compression are concentrated on the Al side, dominated by 1/6 and 1/6 dislocations, and the 1/2 and 1/6 dislocations cross the Ti/Al interface from the Al side to the Ti side. It is found that an increase in temperature helps dislocations to form at lower strains, which leads to a decrease in the compressive strength and an increase in the plasticity of the structure. As expected, the Ti volume fraction has a significant impact on the compressive properties of Ti/Al layered composites, and the compressive strength of the material increases with the increase in the Ti volume fraction. At temperatures above 400 K, the reduction rate of compressive strength becomes smaller, which is due to the formation of new ordered metal compounds between Ti and Al. When the volume fraction of Ti is lower than that of Al, plastic deformation mainly occurs on the Ti side, dominated by 1/6 dislocations. In contrast, the types of dislocations across the Ti/Al interface and on the Al side are dominated by 1/2 and 1/2. When the Ti volume fraction becomes comparable with that of Al, the plastic deformation is transferred from the Ti side to the Al side, and the plasticity of the sample decreases. The optimal compressive properties of Ti/Al layered composites are observed at a Ti volume fraction of 40%, which provides guidance for the structural design of Ti/Al layered composites.
In order to realize the high efficiency and precision clamping of large workpieces with several processes and multiple species processing, the distribution number and position of the zero point clamping unit in the flexible quick-change process system for big thin-walled cylindrical structural parts are presented. The error model of the flexible quick-change process system is established by the Monte Carlo method, which is used to optimize the system structure design. The error variation of the flexible quick-change process system under the action of transposition and extreme working conditions such as cutting force is revealed, and further analysis on the sensitivity of the workpiece’s global displacement error and global attitude error to each error source is carried out. After the optimization, a high-quality, cost-effective, flexible quick-change clamping system is created. The three-coordinate measurement experiment is used to test the functionality and accuracy of the flexible quick-change process system. A significantly improved level of the system’s repetitive positioning accuracy (less than 0.01 mm) is detected. Importantly, the flexible quick-change system obtained by the combinatorial optimal design method has been successfully applied to the production of aerospace components with improved quality and efficiency.
The unique cutting–burnishing coupling effect in BTA deep hole drilling generates a high-hardness and -brittleness white layer (ultrafine martensitic layer), which will degrade component performance and accelerate tool wear. This work investigated the formation mechanism and the mechanical properties of the white layer generated in three distinct regions (the cutting edge radius zone, cutting–burnishing corner zone, and guide pad edge zone) through nanoindentation, SEM and BSE. The microstructure and thickness of the white layer under different feedrates are investigated. The correlations between the white layer, the structure of guide pads, and wear behaviors of the TiN- and TiCN/Al2O3-coated guide pads are revealed. Variations in hardness are observed across different zones. The white layer undergoes a soft-to-hard transition due to rapid quenching and the cutting–burnishing effect at the sharp corner. The highest hardness (9.758 GPa) was observed in the guide pad zone, accompanied by grain refinement. The chamfered TiN-coated guide pad exhibits superior wear resistance but suffers fatigue cracking and adhesive wear in the initial guiding zone. The TiCN/Al2O3-coated pad with rounded corners experiences brittle spalling in the mid-to-rear guiding zone. These findings enhance the understanding of the white layer formation in deep hole drilling and provide a foundation for tool optimization.